Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
Unpack the machine and its components. Check that you have the following: Main unit FX3 cartridge Support trays (2) . Multi-purpose Multi-purpose tray Document support tray cover Paper loading warning label Power cord Telephone line cord . Documentation (Set-Up Sheet, Basic Guide, Handset Handset cradle Screws with Warranty, Registration card) plugs (2) FAXPHONE L75 software CDROM Destination labels NOTE • You need a USB cable (less than 16.4ft./5m) to connect your machine to a computer. • To lift the machine, hold it firmly and level as illustrated. Remove the shipping materials from the machine. 1 Place the machine on a flat surface. 2 Remove all shipping tapes from the exterior of the machine. 3 Gently open the operation panel 1(it only opens partially) and remove the protective sheet 2from the ADF. 4 Close the operation panel by pressing the center down until it locks into place. Assemble the machine. 1 2 A USB label A NOTE • Do not remove the USB label Aat this stage. 1 Attach the paper loading warning label. 2 Insert the document support into the slots on the machine. 3 Insert the multi-purpose tray into the slots on the machine. 4 Insert one of the support trays into the slots above the delivery slot. 5 Insert the other support tray into the slots above the ADF. Load paper. 1 Insert a stack of paper into the multi-purpose tray 1 (print side facing you and top edge first), then adjust the paper guides A to the width of the paper 2. 2 Attach the multi-purpose tray cover to prevent dust accumulating inside the machine. 1 2 2 A Attach the handset to the machine. 1 Remove the screws A from the plugs B and insert the plugs into the holes on the handset cradle. B B A 2 Turn the machine so that the left side is facing you and the right side is against a wall. 3 Insert the plugs (with the handset cradle) into the holes on the machine. 4 Use a cross-point screwdriver or a coin to push the screws into the plugs. Make sure the screws are pushed in as far as they will go. • NOTE If the screws are not pushed fully into the plugs the handset cradle will not be securely attached to the machine. Connect the handset and telephone line cord. Connect the power cord. When the power cord is plugged into the machine and into the wall outlet, the machine is turned on. The LCD displays PLEASE WAIT, then PUT IN CARTRIDGE.The LCD returns to the standby display when you install the cartridge. • Telephone or answering machine • Telephone and answering machine Connect external devices as follows: Telephone line Telephone or answering machine Telephone line Answering machine LINE TEL Telephone Machine Machine • Built-in computer modem and telephone Telephone line Computer LINE TEL Telephone Machine = Telephone line jack = External device jack = Handset jack Handset Place the handset in the cradle. Connect the cord to the h jack. External device Connect the cord of an extension telephone, answering machine or data modem to the t jack. Telephone line cord Connect the supplied cord to the L jack. Then connect the other end to the telephone line jack on your wall. Install the FX3 cartridge. 1 Lift the latch and open the front cover. 2 Remove the cartridge from its protective bag. 3 Gently rock the cartridge from side to side a few times to distribute the toner evenly inside it. •Print quality may be poor if the toner is unequally distributed. 4 Place and hold the cartridge on a flat, clean surface, then gently pull on the plastic tab to remove the plastic seal. 5 Hold the cartridge by its handle and insert it into the machine as far as it will go, making sure that its side tabs are aligned with the guides inside the machine. 6 Use both hands to close the front cover. NOTE • Do not open the drum protective shutter on the cartridge. NOTE • Use a firm, even pull to remove the seal. TOP VIEW SIDE VIEW PULL WITHIN THIS RANGE PULL WITHIN THIS RANGE Set the fax receive mode. Press Receive Mode until the mode you want appears: ex. You can select from the following: Fax/Tel Mode: When the handset or the extension telephone is connected to the machine, the machine automatically switches between faxes and voice calls. MANUAL MODE: When the handset or the extension telephone is connected to the machine, you can receive faxes by pressing Start/Copy before hanging up the handset or the extension telephone. FAX ONLY MODE: If you use your machine to receive only faxes. ANS.MACHINE MODE: If you want to receive faxes automatically and route voice calls to an answering machine. DRPD: To distinguish between fax and voice calls by using Distinctive Ring Patterns. After a few seconds the LCD changes to this display. ex. IMPORTANT • This machine is set to automatically adjust its clock time in accordance with the daylight saving time system. If necessary you can disable this feature (see User’s Guide p.3-9). Fax/Tel Mode Fax/Tel Mode Alarm StopHook Coded DialPause Receive Mode Redial Start/Copy Image Quality Set Set the fax receive mode. Press ...