Votos - 2, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Unpack the machine and its components. Check that you have the following: NOTE • You need a USB cable (less than 16.4 ft./5 m) to connect your machine to a computer. • To lift the machine, hold it firmly and level as illustrated. . Machine . FX-3 S Cartridge . Support trays (2) . Multi-purpose tray . Multi-purpose tray cover . Document support . Handset . Handset cradle . Plugs with pins (2) . Paper loading warning label . Power cord . Telephone line cord . Documentation Set-Up Instructions Basic Guide Warranty Registration card (for USA only) . FAXPHONE L80 Software CD-ROM . Destination labels Remove the shipping materials from the machine. 1 Place the machine on a flat surface. 2 Remove all shipping tapes from the exterior of the machine. 3 Gently open the operation panel . (it only opens partially) and remove the protective sheet . from the ADF. 4 Close the operation panel by pressing at the center until it locks into place. Assemble the machine. USB label .. NOTE • Do not remove the USB label on the back of the machine at this stage. Multi-purpose tray Support tray Document support Paper loading warning label Multi-purpose tray cover 1 Attach the paper loading warning label. 5 Insert the document support into the slots on the machine. 2 Insert the multi-purpose tray into the slots on the machine. 3 Insert one of the support trays into the slots above the delivery slot. 4 Insert the other support tray into the slots above the ADF. NOTE • Place the multi-purpose tray cover on the machine after loading paper (see the next page). Load paper. 1 Insert a stack of paper into the multi-purpose tray . (print side facing you and top edge first), then adjust the paper width guides to the width of the paper .. 2 Attach the multi-purpose tray cover to prevent dust accumulating inside the machine. .... Paper width guide Multi-purpose tray cover Attach the handset cradle to the machine. 1 Insert the plugs with pins into the holes on the handset cradle. Plug with pin NOTE •Do not push the pins all the way into the plugs at this stage. 2 Turn the machine so that the left side is facing you. 3 Insert the plugs (with the handset cradle) into the holes on the machine. 4 Carefully push the pins into the plugs as far as they will go. NOTE •If the pins are not pushed fully into the plugs, the handset cradle will not be securely attached to the machine. Connect the handset and telephone line cord. • Telephone or answering machine • Telephone and answering machine Connect external devices as follows: Telephone line Telephone or answering machine Telephone line Answering machine LINE TEL Telephone Machine Machine • Built-in computer modem and telephone Telephone line Computer LINE TEL Telephone Machine = Telephone line jack = External device jack = Handset jack Handset Place the handset on the cradle. Connect the handset cord to the hjack. External device (optional) Connect the cord of an extension telephone, answering machine or data modem to the t jack. Telephone line cord Connect the supplied cord to the Ljack. Then connect the other end to the telephone line jack on your wall. NOTE •You must complete all the steps in this document to receive faxes properly. Connect the power cord. When the power cord is plugged into the machine and into the wall outlet, the machine is turned on. The LCD displays PLEASE WAIT, then PUT IN CARTRIDGE. The LCD returns to the standby display when you install the FX-3 S Cartridge. NOTE •The machine does not have a power switch. Install the FX-3 S Cartridge. 1 Lift the latch and open the front cover. 2 Remove the FX-3 S Cartridge from its protective bag. 3 Gently rock the cartridge from side to side a few times to distribute the toner evenly inside it. •Print quality may be poor if the toner is unequally distributed. 4 Place and hold the cartridge on a flat, clean surface, then gently pull the plastic tab straight out to remove the plastic seal. 5 Hold the cartridge by its handle and insert it into the machine as far as it will go, making sure that its side tabs are aligned with the guides inside the machine. 6 Use both hands to close the front cover. NOTE • Do not open the drum protective shutter on the cartridge. NOTE • Use a firm, even pull to remove the seal. TOP VIEW SIDE VIEW PULL WITHIN THIS RANGE PULL WITHIN THIS RANGE NOTE • Always hold the cartridge by its handle. NOTE • The FX-3 S Cartridge is a starter cartridge supplied with the machine.The replacement cartridge is the FX-3 Cartridge separately available from Canon. 1 PPrreessss FFuunnccttiioonn .... 2 Press Receive Mode .. . 3 Press or . until the mode you . want appears in the LCD: ex. You can select from the following: Fax/Tel Mode: When the handset or the extension telephone is connected to the machine, the machine automatically switches between faxes and voice calls. MANUAL MODE: 01 02 03 04 05 06 07 08 09 DataRegistrationData Registration DelayedTransmissionDelayed Transmission MemoryReferenceMemory Reference ReceiveModeReceive Mo...