Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
Mark the locations of the four mounting holes and the conduit entrance location on the wall. (The conduit entrance is the proper hole diameter for 1/2 inch (13mm) conduit.) 4. Fasten the backplate to the wall where previously marked. RECOMMENDATION: Wood wall - No. 16 (M8) wood screws, 2 3/4” (70mm) long Cement or brick - 1/4” (M6) stud expansion bolts, 3” (76mm) long Hollow wall - 1/4” (M6) toggle bolts, length depends on wall thickness 5. Run service wire to the dryer location and connect to the terminal block. IMPORTANT: All units must be supplied with 3 wire service. Use No. 12 wire or larger, as required by local electrical code. The ground wire must be connected to the dryer backplate. Unit must be installed by a qualified licensed electrician. CONNeCT TO A DeDICATeD CIRCUIT NOT TO exCeeD 20 AmpS. Dryers located in shower rooms or other wet locations should be equipped with ground fault Interrupter(s). 6. Carefully replace the cover using (2) tamper-resistant screws supplied. Be careful not to damage circuit board or sensor. Apply a bead of caulk around edge of cover to wall. meN WOmeN DISABLeD CHILDReN (depends on age) DISCONNECT POWER BEFORE INSTALLING DESUNA LA ELECTRICIDAD ANTES DE HACER REPARACIONES WARNING: FLOOR “A” DO NOT MOUNT TOP SIDE DOWN Figure 1 ALL MODELS10 13/16 (274mm) 2 3/4 (70mm) 9 1/2 (241mm)5/8 (17mm) 9 1/16 (230mm) 7 7/16 (189mm) 5/8 (17mm) 1 5/16 (33mm) 9 1/8 (232mm) 7/8 (22mm) IN WALL CONDUIT ENTRANCE 7/8 (22mm) SURFACE CONDUIT ENTRANCE TOP OWNER’S MANUAL “DR” HAND AND HAiR DRYERS For InstallatIon or servIce assIstance Please call (734) 421-2400 or email: sales@americandryer.com ImPortant: Have Model & Serial No. ready model #______ serIal #______ AmeRICAN DRYeR LImITeD WARRANTY - “DR” All parts of the DR series are warranted to the original consumer purchaser to be free from defects in material and workmanship for a period of ten (10) years from the date of purchase from manufacturer, in the U.S.A. Outside of the U.S.A., two (2) years. On automatic models, the electronic sensor is warranted for five (5) years. Outside of the U.S.A., two (2) years. We will replace FREE OF CHARGE, during the warranty period, any warranted part which proves defective in material and/or workmanship under normal installation, use, and service, excluding normal wear. Replacement parts can be obtained by returning the part, TRANSPORTATION CHARGES PREPAID. You must notify factory prior to returning part or dryer. Any damage to this dryer as a result of misuse, abuse, neglect, accident, improper installation, unauthorized repairs, or any other use violative of instructions furnished by us, WILL VOID THIS LIMITED WARRANTY. THIS LIMITED WARRANTY IS THE SOLE WARRANTY ON OUR PRODUCTS, AND WE DISCLAIM AND EXCLUDE ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. OUR LIABILITY SHALL NOT EXCEED IN ANY EVENT THE REPLACEMENT OR SALE PRICE OF THE ALLEGEDLY NONCONFORMING PRODUCT AND SHALL EXCLUDE LABOR CHARGES. TO THE EXTENT PERMITTED BY LAW WE SHALL NOT BE LIABLE FOR ANY LOSS, COST, EXPENSE, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER BASED UPON WARRANTY (EXPRESS OR IMPLIED), CONTRACT, NEGLIGENCE OR STRICT LIABILITY AND ARISING IN ANY WAY IN CONNECTION WITH THE DESIGN, MANUFACTURE, SALE, USE OR REPAIR OF THE PRODUCT. AMERICAN DRYER, INC. 33067 INDUSTRIAL ROAD, LIVONIA, MI 48150, U.S.A. Telephone (734) 421-2400 • Fax (734) 421-5580 • Email: sales@americandryer.com Revised May 2011 DISCONNECT POWER BEFORE SERVICING DESUNA LA ELECTRICIDAD ANTES DE HACER REPARACIONES WARNING: SeRVICe & mAINTeNANCe OF YOUR DRYeR Each component used in your dryer has been designed to provide years of trouble free service. However, if trouble should develop, it can normally be located by visual examination. Removal or replacement of most parts is simple and can be done without special tools. IF COLD AIR IS COmING FROm THe NOZZLe: Remove the cover and check the heating element. If the element is broken or burned out, replace it. IF NO AIR IS COmING FROm THe NOZZLe AND HeATING eLemeNT GLOWS: Remove the cover and check to see that the fan revolves freely. Check and replace motor, if required. IF NO AIR IS COmING FROm THe NOZZLe AND HeATING eLemeNT IS NOT IN OpeRATION: Check the thermostat. Assuming the thermostat is okay the timer or sensor should be replaced. IF DRYeR WILL NOT SHUT OFF: Make certain the push button returns out fully after being pushed in and released. If button moves freely, replace the timer. AUTOmATIC DRYeRS: Check that circuit board and sensor are clean from dust and lint (carefully dust off). Make sure plastic window is clean on both sides. Foam piece on window must remain intact. When replacing dryer cover, be careful not to damage circuit board or sensor. This dryer is activated by an infrared sensor. Hand dryers operate as long as hands are below nozzle. There is a maximum 80 second running...