Votos - 4, Puntuación media: 4.5
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Press [SET]. Number of recordable • The approximate number of recordable CS images CS images will appear on the monitor screen. Remaining snapshot memory capacity Using BEST SHOT 73 13. Use [8] and [2] to select the second control panel option from the bottom (Trigger Sense). 14. Use [4] and [6] to select the subject movement sensitivity, and then press [SET]. • You can select any one of three sensitivity levels: “High”, “Normal”, or “Low”. • Move Out CS Setting Guide High : For a subject that moves out of the boundary quickly Low : For a subject that moves out of the boundary slowly • Move In CS Setting Guide High : For a subject that moves into the boundary quickly or for a small subject (relative to the boundary) Low : For a subject that moves into the boundary slowly or for a large subject (relative to the boundary) . To shoot using Move Out CS 1. Compose the image so the subject is within the boundary on the monitor screen. 2. Half-press the shutter button. • The camera will adjust exposure and focus automatically. 3. When the boundary on the monitor screen turns green, press the shutter button the rest of the way down. At this time the camera will go into recording standby and start pre-recording images and storing them in a buffer, in accordance with the Prerecord CS shots setting you configured in step 11 under “To setup the camera” on page 72. After the buffer becomes full, new images keep being added while older images are continually being deleted. The camera will start saving images automatically the moment it detects that the subject has moved out of the boundary. •“0 AUTO” flashes on the monitor screen during recording standby and auto recording. Using BEST SHOT 74 4. Image recording will continue until the end of the recording time is reached. • While the camera is in Move Out CS recording standby, you can cancel standby by pressing the shutter button all the way down. You then will be able to shoot images normally. • To stop an ongoing real-time recording operation, press [SET]. 5. Save the CS images (page 52). . To shoot using Move In CS 1. Compose the image at a location where you expect the subject to enter the boundary on the monitor screen. 2. Half-press the shutter button. • The camera will adjust exposure and focus automatically. • In this case, use of manual focus (page 79) to preset a fixed focus is recommended. 3. When the boundary on the monitor screen turns green, press the shutter button the rest of the way down. At this time the camera will go into recording standby and start pre-recording images and storing them in a buffer, in accordance with the Prerecord CS shots setting you configured in step 11 under “To setup the camera” on page 72. After the buffer becomes full, new Boundary images keep being added while older images are continually being deleted. The camera will start saving images to memory automatically the moment it detects the subject has moved into the area within the boundary. •“0 AUTO” flashes on the monitor screen during recording standby and auto recording. Using BEST SHOT 75 4. Image recording will continue until the end of the recording time is reached. • While the camera is in Move In CS recording standby, you can cancel standby by pressing the shutter button all the way down. You then will be able to shoot images normally. • To stop an ongoing real-time recording operation, press [SET]. 5. Save the CS images (page 52). NOTE • Compose the image so the entire subject and its background are within the boundary. Recording may not be performed correctly if there is little difference between the subject and the part of the background enclosed by the boundary. Also, Move Out CS may not record correctly if the subject is not in the center of the boundary. • Move In CS and Move Out CS do not operate correctly if you press the shutter button all the way down. Be sure to half-press the shutter button. After images are pre-recorded, press the shutter button the rest of the way down. • After pressing the shutter button all the way to put the camera into record standby, keep the camera still. Recording may not be performed correctly if you move the camera during record standby. • The camera will shoot only with Continuous Shutter (CS) while this BEST SHOT scene is selected. • To cancel this BEST SHOT scene and enter the Continuous Shutter mode, press C (Continuous Shutter). • The sleep mode and Auto Power Off are disabled while the camera is in record standby. • The camera may not start recording automatically or camera power may turn off when battery power is low. Always make sure that the battery is sufficiently charged before using these features. • To save all of the continuous shutter images, select “Save All” (page 52) as the continuous shutter image save method. If you do, make sure that the memory card loaded in the camera has enough free space to store them. • Zoom is disabled, and focus and exposure are fixed while the camera is in recording standby. Using BES...