Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
appears on the monitor screen when shooting. Images are not This camera cannot display non-DCF images recorded onto a displayed. memory card using another digital camera. Images cannot be Note that you cannot edit the following types of snapshots. edited (with • Snapshots created using MOTION PRINT resizing, trimming, •Movies date/time editing, • Snapshots recorded with another camera rotation). File Deletion A file cannot be 1)The file may be protected. Unprotect the file (page 87). deleted. 2)“U Disabled” setting may be “On”. Change the setting to “Off” (page 149). Hybrid-GPS I can’t receive GPS 1)“Off” may be selected for the “GPS” setting. Change the waves. “GPS” setting to “On” (page 92). Note that positioning may sometimes take a number of minutes to complete. 2)You are indoors, near buildings, or in some other environment where the camera is unable to receive waves from GPS satellites. In outdoor area where there is an unobstructed path to the sky, point the camera’s GPS antenna upwards toward the sky and hold it still so it can receive waves. 3)The camera stops receiving GPS waves after you turn it off and stop moving it. Turn on the camera. 4)GPS sensitivity will be reduced when there is a nearby device transmitting or receiving strong radio waves. Move the camera away from the device causing the problem. 5)GPS waves cannot pass through some types of glass. If you suspect that such glass between the camera and the sky may be causing the problem, move to another location where there is no glass. Appendix 173 Problem Possible Cause and Recommended Action Positioning takes a long time. 1)The first positioning operation you perform with the camera after you purchase it, immediately after changing the “GPS” setting from “Off” to “On”, or after not using it for a long time may take a number of minutes to complete. 2)Normally, a positioning operation should take around 10 seconds. However, changes in the positions of the GPS satellites, as well as the shooting location and environment can cause it to take longer. 3)Positioning may take longer than normal in environments where GPS satellite wave reception is poor (page 97). The position 1)Depending on wave conditions, GPS satellite positioning is reading is off. subject to error of hundreds of meters. 2)Performing positioning in an environment where it is difficult to receive GPS satellite waves and where the motion sensor is being influenced by magnetism can result in large errors in positioning readings. 3)Performing positioning for a long time with the motion sensor in an environment where it is difficult to receive GPS satellite waves can cause large errors in the positioning readings. There is large error in direction information. 1)The camera may be being affected by magnetism. Perform direction sensor accuracy adjustment (page 106). Also, move the camera away from sources of magnetism and from metal. 2)The direction sensor may not be able to perform direction measurements under any of the following conditions. • Immediately after “On” is selected for the “GPS” setting (page 92) • Immediately after loading the battery and turning on the camera The place name is This can happen immediate after you turn on the camera, when different from the the GPS wave condition icon (page 93) shows (wave location where I condition poor), or when there are major differences between shoot an image. you current location and the place name data stored in camera memory. If this happens, select “- - -” (blank) for the place name (page 94). No place name 1)There may not be a landmark near your current location. appears on the 2)There may not be a name in the camera’s built-in place name camera screen. data in the vicinity of your current location. This will be indicated by “- - -” (blank) appearing on the screen in place of place name candidates (page 95). Appendix 174 Other The wrong date and time are displayed, or the wrong date and time are being stored along with image data. The date and time setting is off. Set the correct date and time (page 146). The messages on the display are in the wrong language. The wrong display language is selected. Change the display language setting (page 147). Images cannot be transferred over a USB connection. 1)The USB cable may not be connected securely. Check all connections. 2)The wrong USB communication protocol is selected. Select the correct USB communication protocol in accordance with the type of device you are connecting (pages 122, 131). 3)If the camera is not turned on, turn it on. 4)Your computer may not be able to recognize the camera if you connect via a USB hub. Always connect directly to the computer’s USB port. Language selection screen appears when the camera is turned on. 1)You did not configure initial settings after purchasing the camera or the camera may have been left with a dead battery. Check the camera setup (pages 20, 147). 2)There may be a problem with the camera’s memory data. If this is the case, perform the...