Votos - 3, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Viewing Snapshots and Movies 67 Zooming an On-screen Image Zooming an On-screen Image 1. In the PLAY mode, use [4] and [6] to scroll through the images until the one you want is displayed. 2. Slide the zoom controller towards z ([) to Zoom factor zoom. You can use [8], [2], [4], and [6] to scroll the zoomed image on the monitor screen. Slide the zoom controller towards w to unzoom the image. – When monitor screen contents are turned on, a graphic in the lower right corner of the screen shows what part of the zoomed image is currently displayed. – To exit the zoom screen, press [ ] (Delete). – Though the maximum image zoom factor is 8X, certain image sizes may not allow zooming up to the full 8X. • Pressing [SET] will lock the current zoom factor for the on-screen image. You can then use [4] and [6] to scroll between images, using the same zoom factor. Pressing [SET] again will unlock the zoom factor and allow you to use [8], [2], [4] and [6] to move around the currently displayed images. Image area Current display area Displaying the Image Menu 1. In the PLAY mode, slide the zoom controller Boundary towards w (]). Use [8], [2], [4] and [6] to move the selection boundary around the image menu. To view a particular image, use [8], [2], [4], or [6] to move the selection boundary to the image you want and then press [SET]. Viewing Snapshots and Movies 68 Viewing Snapshots and Movies on a TV Screen Viewing Snapshots and Movies on a TV Screen 1. Use the AV cable that comes with the camera to connect it to the TV. Yellow AV cable (bundled) [USB/AV] port White VIDEO IN jack (yellow) AUDIO IN jacks (white) TV Audio Video Making sure that the mark on the AV cable connector is towards the lens side, connect the cable to the camera. • Make sure that you insert the cable connector into the USB/AV port until you feel it click securely into place. Failure to insert the connector fully can result in poor communication or malfunction. • Note that even while the connector is fully inserted, you still will be able to see the metal part of the connector as shown in the illustration. 2. Turn on the TV and select its video input mode. If the TV has more than one video input, select the one where the camera is connected. 3. Press [p] (PLAY) to turn on the camera. This will cause an image to appear on the TV screen, without anything appearing on the camera’s monitor screen. • Pressing [ON/OFF] (Power) or [r] (REC) will not turn on the camera while the AV cable is connected. • You also can change the aspect ratio of the screen and the video output system (page 113). 4. Now you can display images and play back movies as you normally do. Viewing Snapshots and Movies 69 IMPORTANT! • Before connecting to a TV to display images, be sure to configure the camera’s [r] (REC) and [p] (PLAY) buttons for “Power On” or “Power On/Off” (page 111). • Audio is initially output by the camera at maximum volume. When you first start displaying images, set the TV volume control at a relatively low level and then adjust it as required. NOTE • Audio is monaural. • Certain TVs may cut off part of the images. • All icons and indicators that appear on the monitor screen also appear on the TV screen. You can use [8] (DISP) to change the display contents. Recording Camera Images to a DVD Recorder or Video Deck Use one of the following methods to connect the camera to the recording device using the camera’s bundled AV cable. – DVD recorder or video deck: Connect to the VIDEO IN and AUDIO IN terminals. – Camera: USB/AV port You can play a slideshow of snapshots and movies on the camera and record it on a DVD or video tape. When recording images to an external device, use [8] (DISP) to clear all indicators from the monitor screen (page 12). For information about connecting a monitor to the recording device and about how to record, see the user documentation that comes with the recording device you are using. Viewing Snapshots and Movies 70 Other Playback Functions (PLAY) This section explains menu items that you can use to configure settings and perform other playback operations. Using the PLAY Panel Pressing [SET] in the PLAY mode will display the PLAY Panel. . Example PLAY Panel Operation 1. In the PLAY mode, press [SET]. [8] [2] PLAY Panel The PLAY Panel will appear along the right side of the monitor screen. 2.Use [8] and [2] to select the PLAY Panel item you want, and then press [SET]. [SET] 3. The following describes the operations you can perform for each of the PLAY Panel items. Exita Exits the PLAY Panel. Playback Start P The operation that is performed when this item is selected depends on the type of file that is currently displayed on the monitor screen. • Movie: Starts movie playback (page 67). • Voice recording: Starts voice recording playback (page 51). • Audio snapshot: Starts audio playback (page 77). Slideshow a Displays a slideshow menu. See “Playing a Slideshow on the Camera (Slideshow)” (page 73) for slideshow menu operations. Rotation y Di...