Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Confirm that the positive (+) and negative (–) terminals are oriented correctly as described on the label at the entrance of the battery chamber, and insert the battery. Use the side of the battery to push the orange battery latch up 1 as the battery is inserted 2. The latch drops back into place when the battery is fully inserted. j Inserting the Battery Inserting the battery upside down or backwards could damage the camera. Be sure to check the battery is in the correct orientation. 3 Close the battery-chamber/memory card slot cover. 1 2 2 1 Inserting the Battery Removing the Battery Turn the camera off before removing the battery. To eject the battery, open the battery-chamber/ memory card slot cover and slide the battery latch in the direction shown 1. The battery can then be removed by hand 2. • Note that the battery may become hot during use; observe due caution when removing the battery. First Steps 12 j Note on the Battery Be sure to read and follow the warnings for the battery on page iii and the section, “Caring for the Camera” (c153), before using the battery. 15 Charging the Battery Insert the battery and charge it with the AC Adapter EH-64 (supplied) before first use or when the battery is running low. First Steps 1243 1 Connect the power cable and AC adapter 1. 2 Turn off the camera. If the power-on lamp (green) is lit, press the power switch to turn off the camera. You cannot charge the battery while the camera is turned on. 3 Connect the AC adapter to the camera’s multi connector 2. The multi connector should be fully inserted. 4 Plug the power cable into an outlet 3. The AC adapter power-on lamp will light 4. k Charging the Battery After Setting the Camera’s Clock When the camera’s built-in clock has not been set, the battery begins charging when the AC adapter is connected. Once the clock is set, Picture Bank (c144) will start when the AC adapter is connected, and the camera will attempt to upload pictures to the my Picturetown server. Press d to cancel picture upload and charge the battery. Picture Bank can be set so that it does not start automatically when the AC adapter is connected (c145). 5 The battery begins charging. The power-on lamp net to the power switch will blink orange as the battery charges. If the lamp flickers rapidly, the AC adapter is not correctly inserted or the battery is faulty. Reinsert the AC adapter or replace the battery. A fully exhausted battery will recharge in about two hours. 16 Charging the Battery 6 Charging is complete. The power-on lamp (orange) stops blinking when charging is complete. 7 Disconnect the camera and AC adapter. Disconnect the AC adapter from the camera’s multi connector. Be sure to unplug the power cable from the power outlet. Turning On and Off the Camera To turn on the camera, press the power switch. The power-on lamp (green) will light and the monitor will turn on. To turn off the camera, press the power switch again. First Steps If the camera is turned off, hold down i to turn the camera on in playback mode (c28). j Note on the Power Cable Supplied for the Camera (c16) Only use the power cable for the AC Adapter EH-64 (supplied) for the COOLPIX S51c. l Connecting the AC Adapter EH-64 The AC Adapter EH-64 (supplied) can: • When the camera is turned on, power the camera from a power outlet. • When the camera is turned off, charge the battery in the camera (c16). It can also be used to power the camera for playback, data transfer, or printing (recommended). Do not, under any circumstances, use another make or model of AC adapter. Failure to observe this precaution could result in fire or product malfunction. The AC adapter and the supplied audio video/USB cable cannot be used at the same time. l Charging the Battery with the Battery Charger The Rechargeable Li-ion Battery EN-EL8 can also be charged using the Battery Charger MH-62 (available separately from Nikon) (c150). 17 Setting Display Language, Date, and Time A language-selection dialog is displayed the first time the camera is turned on. 1 Press the power switch to turn on the camera. The power-on lamp will light and the monitor will turn on. 2 Use the rotary multi selector to choose the desired language and press d. For information on using the rotary multi selector, see “The Rotary Multi Selector” (c11). 3 Choose [Yes] and press d. If [No] is selected, the date and time will not be set. Date Set time and date? No Yes 4 Press d. The home time zone menu is displayed. l Daylight Saving Time If daylight saving time is in effect, turn on [Daylight saving] in the time zone menu and set the date. 1 Before pressing d, press the rotary multi selector Hto choose [Daylight saving]. 2 Press d to enable daylight saving time (y). Pressing d toggles the daylight saving time option on and off. 3 Press the rotary multi selector G, and then press d to proceed to step 5. When daylight saving time ends, turn [Daylight saving] off from the date menu (c107) in the setup menu. The camera’s clock is aut...