Votos - 0, Puntuación media: 0
(
)
)
|
Fotos y especificaciones Olympus UFL-2 |
Resumen del manual
Once the grease has permeated throughout the O-ring, check it for damage or irregularities (both visually and by touch). If you notice any abnormalities, replace the O-ring with a new one. 4 Apply the grease to the O-ring contact surface. Use any residual grease on your fingertips to clean and lubricate the O-ring contact surface on the battery cap. EN time, confirm that the O-ring does not stick out from the groove. CAUTION • Always perform maintenance of the waterproof function even when the battery cap has been opened to exchange the battery. Neglecting this maintenance may result in water leakage. • When the flash is not to be used for a long time, remove the O-ring from the groove to prevent deformation of the O-ring, apply a thin coat of silicone grease, and store it in a clean plastic bag. • When drying is done with salt attached, it is likely that a function impairment will be caused. After use, always wash off any salt. EN 17 EN 18 EN 3. Inserting the Batteries Usable batteries (sold separately) Always use one of the following battery combinations: AA alkaline batteries/AA NiMH batteries/AA lithium batteries/ AA oxyride batteries/AA NiCd batteries • Manganese batteries are not to be used. Inserting the batteries 1 Carefully rotate the battery cap counterclockwise to remove it. 2 Install the batteries in the correct manner paying especial attention to match the (+) and (-) marks. 3 Make sure to check that there is no foreign matter, rubbish etc. not only on the O-ring but also on the contact surface (battery cap side). 4 Thinly apply the specified silicone O-ring grease to the O-ring. 5 Match the O mark on the battery cap (back side) with the O mark on the flash and while pushing the battery cap, turn gently in a clockwise direction until it can’t turn anymore. • While putting the cap back on take special care so that the O-ring does not project from the groove. 6 After replacing the battery cap tightly, turn it back slightly in a counterclockwise direction and align the marks. • After aligning the marks, make sure no O-ring can be seen. +- O Mark Alignment marks O-ring Correct (The O-ring can’t be seen) Incorrect (The O-ring can be seen) 1 2 4 5 6 r2090_e_00.book Page 18 Thursday, May 1, 2008 6:29 PM r2090_e_00.book Page 19 Thursday, May 1, 2008 6:29 PM CAUTION • While installing and exchanging batteries make sure to wipe the flash of any water and always use dry hands. Pay especial attention for any drips from hair and wetsuits. • Turn gently and slowly when taking on/off the battery cap. If the cap is turned too quickly the O-ring may get caught and cause a leakage. • When securing the battery cap tightly, make sure to turn it back slightly in a counterclockwise direction and align the flash’s mark with the battery cap’s mark. If the battery cap is secured too tight beyond the alignment marks, the battery cap may not be removed due to water pressure etc. • Make sure to use the same type of batteries. • Always replace both batteries at the same time. EN EN 19 r2090_e_00.book Page 20 Thursday, May 1, 2008 6:29 PM 4. Mounting the Flash Attaching to an arm Attach the flash to the arm. When attaching the arm to the camera, make sure to read the arm’s instruction manual on how to attach the arm. 1 Loosen the arm mount knob by turning in an counterclockwise direction. 2 Place part A in the space between the arm mount. 3 Turn the loosened knob, in step 1, in a clockwise direction all the way to clamp the arm to the flash. • Be sure to double check the arm is firmly fastened to the flash. EN 1A23 If the case of necessity, attach the flash leash to the flash leash hole and tie it to the underwater case, etc. EN 20 r2090_e_00.book Page 21 Thursday, May 1, 2008 6:29 PM Connecting to a camera’s underwater case There are two ways to connect the flash to a camera’s underwater case. To learn what connection method to use, refer to the instruction manual that comes with your camera’s underwater case. Connecting using an underwater fiber optic cable (optional) EN • Insert the plugs of the underwater fiber optic cable into the connector on the camera’s underwater case and on the flash’s fiber optic cable connector, all the way in until they stop. • You can connect and disconnect the underwater fiber optic cable while under water. • For further details, refer to the instruction manuals of the underwater fiber optic cable (optional) and the camera’s underwater case. EN 21 EN 22 EN Connecting using an underwater TTL cable (optional) and hot shoe cable (optional) 1 Verify that the flash is completely dry. 2 Remove the cap of the TTL cable connector on the flash. Inspect the O-ring and apply a thin coating of the supplied silicon grease. 3 Remove the cap from the TTL cable’s connector. 4 Align the TTL cable’s plug and the TTL cable connector on the flash at their alignment marks and insert the cable straight. 5 Turn the lock dial on the cable’s connector until it stops to firmly attach the connector. 6 In the same way, ...
Otros modelos de este manual:Cámaras - UFL‑2 (2.77 mb)