Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Make sure the engine stop cable is assembled correctly. Before you operate the unit, replace a bent or damaged engine stop cable. HOW TO START ENGINE WARNING: The blade will rotate when the engine runs. IMPORTANT: Before you start the engine, operate the engine stop lever several times. Make sure the engine stop cable moves freely. NOTE: The engine design does not include a throttle control or an engine speed adjustment. The engine is set at the best speed for cutting grass, bagging grass, and for extended engine life. 1. Check the oil. 2. Fill the fuel tank with regular unleaded gasoline. Make sure the gasoline is clean. Leaded gasoline will increase deposits and shorten the life of the valves. NOTE: Do not use gasohol or methanol. Do not use premium unleaded gasoline. WARNING: Always use a safety gasoline container. Do not smoke when adding gasoline to the fuel tank. When inside an enclosure, do not add gasoline. Before you add gasoline, stop the engine and let the engine cool for several minutes. 3. Make sure the spark plug wire is connected to the spark plug. 4. The primer button is on the side of the engine (Figure 9). Push the primer button. Every time you push the primer button, wait two seconds. For the number of times required to push the primer button, see the engine manufacturer’s instructions. Primer Button Figure 9 NOTE: Do not use the primer button to start a warm engine. 5. Stand behind the mower (Figure 10). Use one hand to hold the engine stop lever in the operating position as shown. Use the other hand to hold the recoil-start grip. 6. Make sure the recoil-start rope is not obstructed or caught between the upper and lower handles.Rapidly pull the recoil- start grip. Slowly return the recoil-start grip. 7. If the engine does not start in 5 or 6 tries, See the “Problem and Repair” Instructions. Hold the engine stop lever in the operating postion. Recoil-Start Grip Figure 10 F-050414L 14 MAINTENANCE ENGINE MAINTENANCE Use the following maintenance section to keep your unit in good operating condition. All the maintenance information for the engine is in the “Engine Instruction Book”. Before you start the engine, read this book. WARNING: Before you make an inspection, adjustment (except carburetor), or repair, stop the engine and disconnect the wire from the spark plug. ENGINE TIPPING When you service the engine, inspect the blade, or clean the underside of the mower housing; make sure to always tip the engine with the spark plug up (see Figure 11). Transporting or tipping the engine with the spark plug down will cause: . Hard starting. . Engine smoking. . Spark plug fouling. . Oil or gas saturation of the air filter. Figure 11 HOW TO CLEAN THE MOWER HOUSING WARNING: The blade will rotate when the engine runs. Before you clean the mower housing, stop the engine and disconnect the wire from the spark plug. Grass and other debris can keep the mower from working correctly. After you mow, clean the mower housing as follows. 1. Stop the engine. 2. Disconnect the wire from the spark plug. 3. Clean dirt and debris from the top and the bottom of the mower housing. Clean with soap and water. Wipe off excess water before storage. LUBRICATION 1. For maximum performance, lubricate the wheels and all pivot points with engine oil every 25 hours. 2. To lubricate the engine, refer to the “Engine Instruction Book”. NOTE: Do not lubricate the engine stop cable. Lubricants will damage the cable and prevent the cable from moving freely. Replace the cable if bent or damaged. HOW TO ADJUST THE HEIGHT OF CUT WARNING: The blade will rotate when the engine runs. Before you change the height of cut, stop the engine and disconnect the wire from the spark plug. To change the height of cut, move the position of the adjuster arm at each wheel (Figure 12). Make sure each adjuster arm is in the same position so that the mower will cut level. 1. Disengage the adjuster arm. 2. Move the adjuster arm to another position. Adjuster Arm Figure 12 F-050414L 15 MAINTENANCE BLADE SERVICE WARNING: Before you inspect the blade or the blade adapter, disconnect the wire to the spark plug. If the blade hits an object, stop the engine. Disconnect the wire to the spark plug. Check the unit for damage. Frequently check the blade for wear or damage such as cracks. Frequently check the bolt that holds the blade. Keep the bolt tight. If the blade hits an object, stop the engine. Disconnect the wire to the spark plug. Check the blade adapter for damage. Check for a bent or damaged blade, a badly worn blade, or other damage. Before you operate the unit, damaged parts must be replaced with factory replacement parts. For safety, replace the blade every two years. Keep a sharp edge on the blade. A blade that is not sharp will cause the ends of the grass to become brown. Remove the blade as follows. HOW TO REMOVE THE BLADE WARNING: Before you remove the blade, disconnect the wire to the spark plug. The blade has sharp edges. When you hold the blade, u...
Otros modelos de este manual:cortadoras de césped - 22 (544.46 kb)
cortadoras de césped - 22 (544.46 kb)
cortadoras de césped - 22 (544.46 kb)
cortadoras de césped - 22 (544.46 kb)