Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Use 1/4-20 x 1 screw (D) as shown. Tighten hardware. 2. Install strap (E) to screw (D) securing with 1/4-20 locknut (F). B D B F A E C Figure 9. Install Handle to Tube A. Handle B. Locknuts, KEPS, 1/4-20 C. Screw, Slotted, 1/4-20 x 1/2 D. Screw, Slotted, 1/4-20 x 1 E. Strap, Rubber F. Locknut, Center Lock, 1/4-20 Assembly 9 10 Figure 12. Install Cover Assembly A. Bag Support Bracket B. Cover Assembly C. Cover Hinge Pins D. Hair Pins E. Hinge Pivots D INSTALL COVER ASSEMBLY 1. Attach cover assembly (B, Figure 12) to bag support bracket (A) using hinge pivots (E). Secure cover using cover hinge pins (C) and hair pins (D) as shown. C E A B C D E Figure 11. Attach Hitch and Upright Support A. Hitch and Upright Support Assembly B. Frame spacers A INSTALL HITCH AND UPRIGHT SUPPORT ASSEMBLY 1. Attach hitch and upright support assembly (A, Figure 11) to frame spacers (B) as shown. A B B INSTALL BAG AND COVER SUPPORT 1. Install the bag and cover support (B, Figure 10) to upright support (A) using reinforcement plate (C) and 3/8-16 x 1 capscrews (D) and 3/8-16 locknuts (E) as shown. A C B Figure 10. Install Bag and Cover Support A. Upright Support B. Bag and cover Support C. Reinforcement Plate D. Capscrews, 3/8-16 x 1 E. Locknuts, 3/8-16 E D Assembly 11 INSTALL COLLECTOR BAGS 1. Raise the cover (A, Figure 13). 2. Attach collector bags (B) using grass bag hanger (C) to bag hanger post (D). Figure 13. Install Collector Bags A. Cover B. Collector Bag C. Grass Bag Hanger D. Bag Hanger Posts A B C Assembly D INSTALL LOWER DISCHARGE CHUTE 1.Lift discharge deflector up (D, Figure 14). 2. Insert lower chute rod (A) into mounting plate (B). 3. Pull rubber strap (C) and secure by placing hole closest to knob in strap completely over locknut (E). C D E A B Figure 14. Install Lower Discharge Chute A. Lower Chute Rod B. Mounting Plate C. Rubber Strap D. Discharge Deflector E. Locknut C A B D C A B D C D A B E 44” Frame Hung Mowers 50” Frame Hung Mowers 44” Free Floating Mowers 50” Free Floating Mowers F Assembly Figure 15. Install Upper Tube to Cover A. Upper Tube B. Cover C. Ridge, Upper Tube D. Ridge Cutout INSTALLING UPPER & MIDDLE TUBES 1. Slide the upper tube (E, Figure 15) into cover (B) aligning ridge (C) with cutout (D) as shown. 2. See Figure 16 for correct hole location and secure the upper tube (E) to middle tube using screw (F). 2. Slide middle tube (D, Figure 16) into upper tube (E). 3. Slide middle tube (D) over boot (A). Pull strap (B) and place hole completely over pin (C). Figure 16. Install Middle Tube A. Lower Chute B. Strap, Rubber C. Pin D. Middle Tube E. Upper Tube F. Screw, 1/4 x 3/4 12 Assembly 13 14 Normal Removal & Installation A. Hitch Support Assembly B. Cover K. Nut & Capscrew C. Pin L. Mounting plate D. Hair Pins M. Lower Chute Rod E. Bag N. Lower Chute F. Grass Bag Hanger O. Pin G. Upper Tube P. Strap, Middle H. Middle Tube Q. Ridge I. Strap, Boot R. Ridge Cutout J. Deflector S. Rear Spacers E Q D B Normal Removal & Installation Collector Installation Note: See previous pages for more detailed installation and operation instructions if necessary. 1. Mount the hitch support assembly (A, Figure 17) onto rear tractor frame spacers (S). 2. Attach cover (B) to support assembly using pins (C) and hair pins(D). 3. Pivot cover (B) up. Install bags (E) by attaching grass bag hanger (F) to support assembly (A). Figure 17. Normal Installation & Removal C P N I O M L J R A K 4. Lift discharge deflector (J) up. Insert lower chute rod (M) into mounting plate (L). Pull strap (I) and secure by placing hole closest to knob in strap completely over locknut and capscrew (K). 5. Slide the upper tube (G) into cover (B) aligning ridge (Q) with cutout (R) as shown. 6. Slide middle tube (H) into upper tube (G). Slide middle tube (H) over lower chute (N). Pull strap (P) and place hole completely over pin (O). F G H D C Normal Removal & Installation S S Collector Removal WARNING OPERATION WITHOUT BAGGER For operation without bagger, the mower deflector MUST be properly installed in the down position and retained by the spring latch. 1. Unhook strap (P, Figure 17) from pin (O). Slide middle tube (H) into upper tube (G) and remove middle tube (H). Remove upper tube (G) from cover (B). 2. Lift up cover (B) remove and empty bags (E). 3. Unhook strap (I) from locknut and capscrew (K). Remove lower chute (N) from mounting plate (L). See that the discharge deflector (J) returns to the DOWN position. 4. Remove hair pin (D) and pins (C) then remove cover (B). Note:To prevent loss of parts, reinstall pins (C) and hair pins (D) in support assembly hinge pivots (E, Figure 17). 5. Remove hitch support assembly (A) from rear frame spacers (S). Normal Removal& Installation 15 MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 Briggs & Stratton Yard Power Products Group Copyright © 2007 Briggs & Stratton...