Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Stop switch/OIL GARD® light (if equipped) 9. Fuel fill 1 2 3 4 5 6 8 7 10. Fuel tank 11. Oil fill/Dipstick (if equipped) 12. Blower housing 13. Oil drain plug 13 11 12 10 14 16 9 15 14. Oil fill cap 15. Engine Model Type Code xxxxx xxxx xx xxxxxxxx 16. Muffler/(Muffler guard, if equipped)/ (Spark arrester, if equipped) GENERAL INFORMATION ENGINE MODEL This is a single cylinder, overhead valve (OHV), air-cooled engine. It is a low emissions engine. In the state of California, OHV Model Series 110000 and 120000 engines are certified by the California Air Resources Board to meet emissions standards for 125 hours. OHV Model Series 200000, 210000 engines are certified by the California Air Resources Board to meet emissions standards for 250 hours. Such certification does not grant the purchaser, owner or operator of this engine any additional warranties with respect to the performance or operational life of this engine. This engine is warranted solely according to the product and emissions warranties stated elsewhere in this manual. Note: For practical operation, horsepower loading should not exceed 85% of rated horsepower. Engine power will decrease 3-1/2% for each 1,000 feet (300 meters) above sea level and 1% for each 10° F (5.6° C) above 77° F (25° C). Engine will operate satisfactorily at an angle up to 15°. MODEL SERIES 110000 Bore. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11/16 in. (68 mm) Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3/64 in. (52 mm) Displacement . . . . . . . . . . . . . . . . . . 11.58 cu. in. (190 cc) MODEL SERIES 120000 Bore. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11/16 in. (68 mm) Stroke . . . . . . . . . . . . . . . . . . . . . . . . . 2-13/64 in. (56 mm) Displacement . . . . . . . . . . . . . . . . . . 12.48 cu. in. (206 cc) MODEL SERIES 200000 Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 3.120 in. (79.23 mm) Stroke . . . . . . . . . . . . . . . . . . . . . . . . 2.438 in. (61.67 mm) Displacement . . . . . . . . . . . . . . . . . . 18.64 cu. in. (305 cc) MODEL SERIES 210000 Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 3.300 in. (83.81 mm) Stroke . . . . . . . . . . . . . . . . . . . . . . . . 2.438 in. (61.67 mm) Displacement . . . . . . . . . . . . . . . . . . 20.85 cu. in. (342 cc) TUNE-UP SPECIFICATIONS Models 110000/120000 Armature air gap . . . 0.010 – 0.014 in. (0.25 – 0.36 mm) Spark plug gap . . . . . . . . . . . . . . . . . . 0.030 in. (0.76 mm) Valve clearance with valve springs installed and piston 1/4 in. (6 mm) past top dead center (check when engine is cold). See Repair Manual P/N 272147. Intake. . . . . . . . . . . . . 0.004 – 0.006 in. (0.10 – 0.15 mm) Exhaust . . . . . . . . . . . 0.009 – 0.011 in. (0.23 – 0.28 mm) TUNE-UP SPECIFICATIONS Models 200000/210000 Armature air gap . . . 0.008 – 0.012 in. (0.20 – 0.30 mm) Spark plug gap . . . . . . . . . . . . . . . . . . 0.030 in. (0.76 mm) Valve clearance with valve springs installed and piston 1/4 in. (6 mm) past top dead center (check when engine is cold). See Repair Manual P/N 272147. Intake. . . . . . . . . . . . . 0.004 – 0.006 in. (0.10 – 0.15 mm) Exhaust . . . . . . . . . . . 0.004 – 0.006 in. (0.10 – 0.15 mm) 6 7 OIL 275092 CAUTION: This engine is shipped from Briggs & Stratton without oil. Check oil level before starting engine. If you start the engine without oil, the engine will be damaged beyond repair and will not be covered under warranty. Note: If this engine is equipped with gear reduction, gear reduction case must be filled with oil prior to operating engine. See gear reduction oil filling instructions on page 12. OIL CAPACITY Model 110000 and 120000 series engines hold approximately 5/8 quart (20 ounces; 0.6 liter). Model series 200000 and 210000 engines hold approximately 7/8 quart (28 ounces; 0.8 liter). TYPE OF OIL TO USE • Use a high quality detergent oil classified “For Service SF, SG, SH, SJ” or higher, such as Briggs & Stratton SAE 30, Part Number 100005 (20 oz) or 100028 (48 oz). • Do not use special additives. • Choose a viscosity according to the table opposite. Note: Synthetic oil meeting ILSAC GF-2, API certification mark and API service symbol (shown at left) with “SJ/CF ENERGY CONSERVING” or higher, is an acceptable oil at all temperatures. Use of synthetic oil does not alter required oil change intervals. °F -20 0 20 40 60 80 100 °C -30 -20 -10 0 10 20 30 40 STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE * ** 32 * CAUTION: Air cooled engines run hotter than automotive engines. The use of non-synthetic multi-viscosity oils (5W-30, 10W-30, etc.) in temperatures above 40° F (4° C) will result in higher than normal oil consumption. When using a multi-viscosity oil, check oil level more frequently. ** CAUTION: SAE 30 oil, if used below 40° F (4° C), will result in hard starting and possible engine bore damage due to inadequate lubrication. SAE Viscosity Grades CHECKING AND ADDING OIL • Check oil level before sta...
Otros modelos de este manual:cortadoras de césped - 110000 (644.79 kb)