Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Make certain that the hole cut is far enough over that it will not interfere with operators foot room. Cut hole through floor mat and floor using a round 2" hole saw (See Figure 12). After you cut the rubber mat with the hole saw pull the piece of rubber out of saw, this will make it easier to cut through the floor. (See Figure 12) 3. Install Cable / Wire Harness Boot Cover. The Boot cover will be modified, using a knife cut an "X" shaped cut across the small hole at the top. This cut will be cut back approx 1/2" from original hole. Using the 4 screws screw the cover to the rubber mat. (See Figure 13 & 14) Figure 10 Existing Threaded holes in RH Door Frame of Cab Control Lever Mounting Bracket Figure 11 Rubber Floor Mat 2" Hole Saw Figure 12 Figure 13 Interstater (NH TS-100A , 115A , 125A & 135A Asy. Manual) 06/04 © 2004 Alamo Group Inc. Page 4 - 4 Remote Control Cable Connections (Cab Tractor) Screw the cover to the Rubber Floor Mat with the screws furnished. Figure 14 Figure 15 4. Install Wire Harness through floor and boot. The Wire harness will come to you with the on / off switches attached, these switches will need to be removes to Push the Wire Harness up through the floor and boot cover (See Figure 15 & 18). 5. Insert Cables up through Boot Cover. Mark the cables as to which is which on the control valve as they need to be connected in the same order on the inside of the cab as they are connected to the control valve (See Figure 17) Remote Control Cable Connections Cab Tractor: (continued) Wire Harness Control cable Cable Cover Boot Figure 16 Mark on Cable to reference which it is on the control valve Figure 17 Figure 18 Switches unpluged and removed to run up through the Fllot and boot cover Screw the cover to the Rubber Floor Mat with the screws furnished. Figure 14 Figure 15 4. Install Wire Harness through floor and boot. The Wire harness will come to you with the on / off switches attached, these switches will need to be removes to Push the Wire Harness up through the floor and boot cover (See Figure 15 & 18). 5. Insert Cables up through Boot Cover. Mark the cables as to which is which on the control valve as they need to be connected in the same order on the inside of the cab as they are connected to the control valve (See Figure 17) Remote Control Cable Connections Cab Tractor: (continued) Wire Harness Control cable Cable Cover Boot Figure 16 Mark on Cable to reference which it is on the control valve Figure 17 Figure 18 Switches unpluged and removed to run up through the Fllot and boot cover Interstater (NH TS-100A , 115A , 125A & 135A Asy. Manual) 06/04 © 2004 Alamo Group Inc. Page 4 - 5 Remote Control Cable Connections (ROPS Tractor) Remote Control Cable Connections ROPS Tractor: 1. Install Valve Stand to Tractor on ROPS Trac- tor only. Attach Valve Stand to the top of the Right Lift Cylinder Support with (3) 1/2" x 1-1/2" bolts, and (3) 1/2" locknuts (See Figure 19). 2. Attcah Valve Stand to Valve Mount Bracket. Attach Valve Stand to the Valve Mount Bracket with (2) 3/8" x 1-1/4" bolts and (2) 3/8" locknuts (See Figure 20). 3. Attach Control Valve to the Valve Stand. Attach Control Valve to the Valve Stand with (2) 3/8" x 1" bolts, (2) 3/8" locknuts. Attach the Top Cover and the Bottom Cover to the Valve Mount Bracket with (8) 3/8" x 1" bolts, (8) 3/8 washers and (8) 3/8" locknuts (See Figure 21). 4. Install Mower Wing ON / Off Switches. Make certain to install connector so that larger brown wires are located on bottom poles of switch. This applies to Dual Wing and Single Wing applications Figure 19 Figure 20 Figure 21 MOWER ON/OFF SWITCH Figure 22 Left or Right On / Off Switch Brown Red Figure 22 Red Brn * Brn *White (for LH Wing Switch) OR Yellow (for RH Wing Switch) Plug as seen from back where wires plug in Remote Control Cable Connections (ROPS Tractor) Remote Control Cable Connections ROPS Tractor: 1. Install Valve Stand to Tractor on ROPS Trac- tor only. Attach Valve Stand to the top of the Right Lift Cylinder Support with (3) 1/2" x 1-1/2" bolts, and (3) 1/2" locknuts (See Figure 19). 2. Attcah Valve Stand to Valve Mount Bracket. Attach Valve Stand to the Valve Mount Bracket with (2) 3/8" x 1-1/4" bolts and (2) 3/8" locknuts (See Figure 20). 3. Attach Control Valve to the Valve Stand. Attach Control Valve to the Valve Stand with (2) 3/8" x 1" bolts, (2) 3/8" locknuts. Attach the Top Cover and the Bottom Cover to the Valve Mount Bracket with (8) 3/8" x 1" bolts, (8) 3/8 washers and (8) 3/8" locknuts (See Figure 21). 4. Install Mower Wing ON / Off Switches. Make certain to install connector so that larger brown wires are located on bottom poles of switch. This applies to Dual Wing and Single Wing applications Figure 19 Figure 20 Figure 21 MOWER ON/OFF SWITCH Figure 22 Left or Right On / Off Switch Brown Red Figure 22 Red Brn * Brn *White (for LH Wing Switch) OR Yellow (for RH Wing Switch) Plug as seen from back where wires plug in Interstater (NH TS-100A , 115A , 125A & 135A Asy. Man...