Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
All safety devices should be inspected carefully at least daily for missing or broken components. Missing, broken, or worn items must be replaced at once to reduce the possibility of injury or death from thrown objects, entanglement, or blade contact. (SGM-3) • Ensure the tailwheel beam position support bolts are properly installed and tightened. • Inspect all bolts and screws and tighten to the recommended torque. OPS-R-0039_B • Ensure the driveline slip clutch shield is in place and in good condition. • Ensure the driveline integral shield is in good condition and rotates freely. • Make sure the tractor PTO master shield is in place, lowered, and in good condition. OPS-R0039_ A OPERATION ©2007 Alamo Group Inc. OPERATION A60B/A72B 02/07 Operation Section 4-20 • Inspect the gearbox oil level. A low oil level is a warning sign that the gearbox may be cracked or its seal is damaged and needs replacement. • Ensure the gearbox vent is in place and free from clogs. OPS-R-0040 • Inspect blades and blade bolts for looseness and excessive wear. Make sure the mower is securely blocked up before crawling beneath. Replace damaged, worn and missing blades as complete sets to maintain rotary balance during operation. • Ensure carrier hub nut is tightened with the cotter pin inserted and spread. OPS-R-0041 OPERATION ©2007 Alamo Group Inc. OPERATION A60B/A72B 02/07 Operation Section 4-21 10.3 Cutting Component Inspection Inspect blade pan and blade assembly for the following: OPS-U-0031 Inspect the Blades daily for abnormal wear. REPLACE BOTH BLADES on that carrier IMMEDIATELY if either blade has: • Become bent or deformed from it’s original shape or • Any cracks are visible, or • Deep gouges in the blade’s surface are persent, or • Gouges or chipped areas in the cutting edge are larger than 1/2”, or • The material on the leading edge has been worn away by more than 1/2” Failure to replace abnormally worn blades may lead to catastrophic failure of the blades and ejection of the broken part with tremendous force which may cause serious bodily injury or death. OPS-U-0032 OPERATION ©2007 Alamo Group Inc. OPERATION A60B/A72B 02/07 Operation Section 4-22 11. DRIVING THE TRACTOR AND IMPLEMENT Safe tractor transport requires the operator possess a thorough knowledge of the model being operated and precautions to take while driving with an attached implement. Ensure the tractor has the capacity to handle the weight of the implement and the tractor operating controls are set for safe transport. To ensure safety while driving the tractor with an attached implement, review the following. OPS-U- 0012 Never run the Tractor engine in a closed building or without adequate ventilation. The exhaust fumes can be hazardous to your health. (SG-23) Transport only at speeds where you can maintain control of the equipment. Serious accidents and injuries can result from operating this equipment at high speeds. Understand the Tractor and Implement and how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly. Before transporting the Tractor and Implement, determine the proper transport speeds for you and the equipment. Make sure you abide by the following rules: • Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly to determine the stopping characteristics of the Tractor and Implement. As you increase the speed of the Tractor the stopping distance increases. Determine the maximum transport speed not to exceed 20 mph (30 kph) for towing this equipment. • Test the equipment at a slow speed in turns. Increase the speed through the turn only after you determine that it is safe to operate at a higher speed. Use extreme care and reduce your speed when turning sharply to prevent the tractor and implement from turning over. Determine the maximum safe turning speed for you and this equipment before operating on roads or uneven ground. • Only transport the Tractor and Implement at the speeds which allow you to properly control the equipment. Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance increases: use extreme care and reduce your speed. When operating in traffic always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and watch out for the other guy. (SG-19) OPERATION ©2007 Alamo Group Inc. OPERATION A60B/A72B 02/07 Operation Section 4-23 11.1 Starting the Tractor The procedure to start the tractor is model specific. Refer to the tractor operator’s manual for starting procedures for your particular tractor. Consult an authorized dealer if the starting procedure is unclear. Ensure the 3-point control lever is in the lowered position and the PTO is disengaged before starting the tractor. OPS-U-0033 11.2 Brake and Differential Lock Setting Make sure the ...
Otros modelos de este manual:cortadoras de césped - 00759354C (40.31 mb)
cortadoras de césped - A60B (40.31 mb)