Votos - 2, Puntuación media: 3 ( )

Fabricar: Alamo Tamaño del archivo: 41.14 mb Nombre del archivo: Idioma del manual:

The first section of this manual includes a list of Safety Messages, that, if followed, will help protect the operator and bystanders from injury or death. Many of the Safety Messages will be repeated throughout the manual. The owner/operator/dealer should know these Safety Messages before assembly and be aware of the hazards of operating this mower during assembly, use, and maintenance. The Safety Alert Symbol combined with a Signal Word, as seen below, is intended to warn the owner/operator of impending hazards and the degree of possible injury faced when operating this machine. The lowest level of Safety Message; warns of possible minor injury. Decals located on the Cutter with this Signal Word are Black and Yellow. Serious injury or possible death! Decals are Black and Orange. Imminent death/critical injury. Decals are Red and White. The front, rear, left, and right are determined by the normal direction of travel, the same as driving an automobile. INTRODUCTION © 2006 Alamo Group Inc. INTRODUCTION A96B 03/06 Introduction Section 2-3 These mowers are available in lift, pull, semi-mount, or hydraulically offset semi-mount type hitch configurations. These rugged Mowers are designed for medium-duty work. They can mow pastures, cut brush up to 2" in diameter, and control grass and weeds on highways or industrial sites. For Non-Agricultural use, OSHA, ASAE, SAE, and ANSI standards require the use of Chain Guards, Deflectors, or Solid Skirts at all times. The Mower manufacturer strongly recommends the use of Chain Guards or Rubber Deflectors for Agricultural purposes as well, to reduce the risk of property damage, serious bodily injury, or even death from objects thrown out by or from contact with the Cutting Blades. The 8' Lift Type machine requires a minimum of 50 HP with adequate front end weight. At least 20% or the tractor’s weight must be on the front tires with the Mower lifted to provide adequate traction for safe steering under good conditions. Slow down on hills, rough terrain, and curves. INTRODUCTION © 2006 Alamo Group Inc. INTRODUCTION A96B 03/06 Introduction Section 2-4 Attention Owner/Operator BEFORE OPERATING THIS MACHINE: 1. Carefully read the Operator’s Manual, completely understand the Safety Messages and instructions, and know how to operate correctly both the tractor and implement. 2. Fill out the Warranty Card in full. Be sure to answer all questions, including the Serial Number of the implement. Mail within 30 days of delivery date of this implement. NOTE: Warranties are honored only if completed “Owner Registration and Warranty” forms are received by Alamo Group within thirty days of delivery of the implement. 3. Record the Blade Model and Serial Numbers on the Warranty page at the front of the Operator’s Manual. Keep this as part of the permanent maintenance file for the implement.. INTRODUCTION © 2006 Alamo Group Inc. ASSEMBLY SECTION Assembly Section 3-1 © 2006 Alamo Group Inc. ASSEMBLY A96B 03/06 Assembly Section 3-2 The A96B Mower will attach to most tractors with Cat. II and lII Quick Hitch. The A96B can be purchased for tractors with 540 or 1000 RPM PTO. DEALER SET-UP INSTRUCTIONS Assembly of this mower is the responsibility of the Alamo dealer. The mower should be delivered to the owner completely assembled, lubricated, and adjusted for normal cutting conditions. Set up mower as received from the factory with these instructions. Open parts box and lay parts out to make location easy. Refer to the parts lists and exploded view drawings for more detail. This mower is shipped partially assembled. Assembly will be easier if components are aligned and loosely assembled before tightening hardware. Always use personal protection devices such as eye, ear and feet protectors during assembly. A-FRAME ASSEMBLY-LIFT TYPE 1. Insert bushing (5) into lower end of each A-Frame half (1 & 2). Position each A-Frame half so the large hole in the top is towards the tractor. Install 3/4” x 2" bolt (10) with Flatwasher (14) through bushing (5) in A-Frame half (1 & 2) and rear hole in inside Main Frame lug. Install locknut. (Figure Asm-R-0134) 2. Install bushing (8) between A-Frame halves (1 & 2) through lower front hole and retain with bolt (12) and locknut (13). 3. Install bushing (8) between A-Frame halves (1 & 2) at upper rear hole location. Install bushings (6) through Braces (3) and install bolt 3/4” x 5" (9), flatwashers (14) and locknut (13) through all parts as shown. Note: Rear braces (3) install to outside of A-frame halves. 4. Attach Braces (3) to Braces (4) with bushings (6), flatwashers (14), bolt 3/4” x 2-1/2” (16), and locknut (13). Retain the rear of Braces (3) together with bushing (15), bolt 3/4” x 2-1/2” (11) and locknut (13) through middle holes in brace (3). Attach braces (4) together with bolt 3/4” x 1-1/2” (17) and locknut (13). 5. Install rear braces (4) to the rear lugs on the Main Frame with bolts 3/4” x 2" (10), flatwashers (14), bushings (6) and locknuts (13). ASSEMBLY © 2...

Descargar ahora

Introduzca dos números de la imagen: