Votos - 0, Puntuación media: 4
(
)
)
|
Resumen del manual
NOTE: There are two additional 1 /4 inch washers below the rear belt cover mounting holes. Be carefull not to lose any of the washers. 3. Remove the two 6 x 12 mm flange bolts from the cover plate on the blower assembly. Remove the cover plate. 4. Unhook the blower drive belt from the mower deck pulley, then remove it from the blower assembly. NOTE: Observe the installed position of the blower drive belt, so you will be sure to replace it correctly. If the belt is reversed on the mower deck pulley during replacement, the blower will run backwards. 114 INCH WING NUTS 114 INCH WING NUT /& I BELT COVER WASHER 114 INCH -- 114 INCH WASHERS 6xl2mm BOLTS BLOWER ASSEMBLY 2.SERVICE DRIVE BELT REPLACEMENT (continued) Installation 1. Install the replacement belt on the blower pulleys, then hook it onto the mower deck pulley. It is important to install the belt correctly; if the belt is reversed on the mower deck pulley, the blower will run backwards. The belt runs from the upper blower pulley to the outer side of the mower deck pulley (the side toward the discharge chute). The belt returns from the inner side of the mower deck pulley (the side toward the middle of the mower deck) to the lower blower pulley. Refer to the illustration on page 8. 2. Install the cover plate on the blower assembly. Tighten the two 6 x 12 mm flange bolts to a torque value of 8.0ft-lb (1.1 kg-m). 3. Install the belt cover, washers, and wing nuts. Refer to the illustration on page 8. Tighten the wing nuts securely. SIDE-DISCHARGE MOWING The grass bags, hopper, bag chutes, and blower can be removed for side-discharge mowing. This permits the side-discharge chute to swing down to its operating position. Objects thrown by the blades can cause serious injury. Before operating the tractor for side-discharge mowing, be sure the side-discharge chute is lowered. BAG, HOPPER, CHUTE, AND BLOWER REMOVAL BAG SUPPORT ASSEMBLY FOR SIDE-DISCHARGE MOWING \I Objects thrown by the blades can cause serious injury. Disengage the Power Take Off (PT.0.h and shut off the engine, before removing equipment. Removal 1. Remove the grass bags (see page 6). 2. Lift the bag support assembly, with hopper top and chutes, off the left and right mounting struts. LEFT STRUT 3. Remove the lower chute (see page 7). NOTE: For side-discharge mowing, you must also remove the blower (see page 10). HITCH PLATE U 2.SERVICE BAG, HOPPER, CHUTE, AND BLOWER REMOVAL FOR SIDE-DISCHARGE MOWING (continued) Installation Install in reverse order of removal. When installing the bag support assembly on the left and right struts, insert the center strut pin in the tractor’s hitch plate hole (see page 9). Refer to page 7 for chute installation instructions. BLOWER REMOVAL FOR SIDE-DISCHARGE MOWING Objects thrown by the blades can cause serious injury. Disengage the Power Take Off (FT.O.), and shut off the engine, before disconnecting the chute sections and removing the blower assembly. Removal NOTE: You must remove the lower chute (see page 7) before you can remove the blower. For side- discharge mowing, also remove the bag support assembly with hopper top, upper chute, and middle BLOWER chute (see page 9). ASSEMBLY 1. Lower the mower deck as far as it will go. 2. Removethe blower drive belt from the mower deck pulley (see page 8). NOTE: Leave the belt on the blower pulleys. Complete belt removal is not necessary for blower removal. 3. Remove the lock pin, and liftthe blower assembly off its mounting bracket. Installation Install in reverse order of removal. Refer to pages 8 and 9 for blower belt installation instructions. Refer to page 7 for chute installation instructions. / MOUNTING BRACKET LOCK PIN IO 3. WARRANTY SERVICE Owner Satisfaction Your satisfaction and goodwill are important to your dealer and to us. All Honda warranty details are explained in the Distributor’s Limited Warranty. Normally, any problems concerning the product will be handled by your dealer’s service department. If you have a warranty problem that has not been handled to your satisfaction, we suggest you take the following action: Discuss your problem with a member of the dealership management. Often complaints can be quickly resolved at that level. If the problem has already been reviewed with the Service Manager, contact the Owner of the dealership or the General Manager. If your problem still has not been resolved to your satisfaction, contact the Power Equipment Customer Service Department of American Honda Motor Co., Inc. American Honda Motor Co., Inc. Power Equipment Division P.O. Box 100021 Duluth, Georgia 30136-9421 Telephone: (404) 497-6400 We will need the following information in order to assist you: -Your name, address, and telephone number -Product model -Date of purchase -Dealer name and address -Nature of problem After reviewing all the facts involved, you will be advised of what action can be taken. Please bear in mind that your problem will likely be resolved at the dealership, using the dealer‘s faciliti...
Otros modelos de este manual:cortadoras de césped - BK4542 (366.77 kb)
cortadoras de césped - GB4500 (366.77 kb)