Votos - 3, Puntuación media: 4 ( )

Fabricar: Ariens Tamaño del archivo: 826.18 kb Nombre del archivo: Idioma del manual:

5. Fill fuel tank. (See Specifications for tank capacity.) 6. Replace fuel cap and tighten. 7. ALWAYS clean up any spilled fuel. 4.4 GENERAL LUBRICATION Swivel Lubrication (swivel units) See Figure 4. Apply Sten Mix Hi-Temp Grease or equivalent to the lube fittings. Order P/N: 00036800 - 3 pack of 3 oz. cartridges. When using Sten Mix Grease for the first time, all components should be thoroughly cleaned prior to lubricating. Commercial Models Grease fittings on rear axle housing every 25 hours. 4 - 22 2 2 Grease Fitting 2. Swivel Lock Hole Figure 4 OM0210 4.5 CHECK MOWER BLADE See Figures 5 and 6. Regularly check mower blades for wear and that lock washer is fully compressed by cap screw (requires 25-30 ft-lbs (33-40 Nm) of torque on cap screw). When blade needs sharpening: 1. Block blade to prevent rotation. 2. Remove cap screw, lock washer and blade from shaft. 3. Sharpen both ends of blade at original angle (25o), removing equal amounts of material from each end to maintain proper blade balance. New blades are balanced to within 1.3 in. oz. at factory. DO NOT grind around corner at tip of blade. If cutting edge of blade cannot be sharpened in a straight line to within 1/8 of an inch of its end, replace blade with Ariens replacement blade only. 4. Install blade, lock washer and tighten cap screw 25-30 ft-lbs (33-40 Nm) until lock washer is fully compressed. IMPORTANT: If mower is used under sandy soil conditions, replace blades when air lifts become eroded. 4.6 CHECK DRIVE BELT Figure 5 1. Cutting Edge 2. Square Corner 3. Air Lift Erosion 4. Air Lift 5. Reverse Lift OM0240 OM0230 1 2 3 4 5 12 3 4 1 4 1. Blade 3. Drive Belt 2 3 2. Cap Screw, Lock 4. Idler Washer & Flat Washer Figure 6 OM0250 Check drive belt for wear or damage. Replace belt if worn or damaged. 4.7 CHECK ENGINE/BLADE CONTROL The engine/blade control must stop the engine and blade within 3 seconds after the bail is released. If the engine or blade continues to run, adjust or repair control immediately. Engine control must stop engine ignition, at 3/4" to 1-1/4" from handlebar as control is released. 4 - 23 To check (Figure 7): To check (Figure 7): . Start engine and slowly release control until engine stops firing. 2. Measure distance between handlebar and control at the point that engine stopped firing. 3. Turn cable nuts at handlebar mount clockwise if measurement is more than 1-1/4" or counterclockwise if measurement is less than 3/4". 4. Turn nuts against mount to lock in position. 2 1 4 3 1. Engine Control 3. Cable Nuts 2. Handlebar 4. Mount Figure 7 OM0280 1-1/8" to 1-5/16" 1 2 3 1. Cable Nuts 2. Bracket 3. Spring Figure 8 There must not be slack in cable. To check, rotate blade in it’s cutting direction (this draws control rod fully in). To eliminate slack in cable, turn nuts on cable at handlebar clockwise. 1 2 3 4 5 S Hook on Some Models 1. Cable Nuts 4. Spring or "S" Hook 2. Bracket 5. Control Rod 3. Spring Figure 9 4.8 CHECK GRASS BAG Check bag for wear or damage. Keep bag clean and dry. Replace only with Ariens original equipment replacement bag. 4.9 CHECK DRIVE CONTROL Check operation of drive control. The drive must disengage completely when the bail handle is released. Adjust bail travel if necessary. See Figure 10. When the wheel drive control is squeezed toward the handlebar, the extension spring, located at the bottom end of the traction cable, must start to extend when the control is between 1-1/2" and 2" (3.8 and 5 cm) away from the handlebar. To check: 1. Squeeze the wheel drive control toward the handlebar until the spring starts to open. 2. Measure the distance between the wheel drive control and handlebar at the handlebar indentation. 3. To obtain the proper adjustment, turn the cable nuts. Turn clockwise if the measurement is more than 2"; counterclockwise if the measurement is less than 1-1/2". Tighten the nuts against the bracket to lock in position. If there is not enough thread length for adjustment, the opposite end of the cable can be adjusted. Three Speed Drive Control When the wheel drive control bail is squeezed toward the handlebar, the extension spring must start to extend when the control bail is between 3-7/8" to 4-1/8" away from the handlebar. The extension spring is located at the bottom end of the traction control cable. 4 - 24 To check the control cable spring: To check the control cable spring: . Squeeze the wheel drive control bail towards the handlebar until the spring starts to open. 2. Measure the distance between the wheel drive bail to the handlebar indentation. 3. To obtain the proper adjustments turn the control cable nuts at the handlebar or the bottom of the control cable anchor against the anchor supports. 4 1. Traction Cable 2. Handlebar Indentation Figure 10 1 2 3 3. Cable Nuts 4. Wheel Drive Control 4.10 HANDLEBAR ADJUSTMENT Holes in handlebar braces provide four height positions, a service position, and a storage position (except on professional models). 1 2 7 3 4 3 5 6 8 1 2 1. Hole...

Descargar ahora

Introduzca dos números de la imagen: