Votos - 2, Puntuación media: 4.5 ( )

Fabricar: Craftsman Tamaño del archivo: 426.68 kb Nombre del archivo: Idioma del manual:

Place hood on cardboard or on a mat to protect paint. . if your tractor has a heat shield shaped like the one in figure 1, temporarily remove it. iMPORTANT: Be sure to reattach the heat shield after bumper is installed. MUFFLER HEAT SHIELD J // FIGURE 1 STEP 2: (SEE HGURE 2) , Place plug (D) on a work bench or solid table and push end of bumper down onto plug. Repeat for a!l four plugs. BUMPER PUSH DOWN W{TH EVEN PRESSURE WORK BENCH OR SOUD TABLE__PLUG FIGURE 2 STEP 3: (SEE FIGURE 3} IMPORTANT: Do not remove any bolts from the tractor frame while the mower deck is raised. Misalignment of holes in frame could result. Lower mower deck to rest on ground. Remove bolts from mounting holes on both sides of tractor frame. Use a mounting bracket to help identify holes. (LT) FRAME (GT) FRAME REMOVE THESE BOLTS REMOVE THESE BOLTS ) NOT ALL (LT) FRAMES HAVE THINSBRACKET FIGURE 3 STEP 4: (SEE FIGURE 4} Attach left mounting bracket to hole shown in left side of tractor frame using bolt (C), lock washer (H) and fiat washer (G). Align middle hole in bracket with empty hole in tractor frame and tighten bolt (C) to hold bracket in place. Repeat for right mounting bracket. (GT) FRAME SHOWN LEFT MOUNTING FLAT BRACKET WASHER BOLT (G} (C) ATTACH TO LOCK THRS HOLE WASHER (H) BUMPER STOPS FACE OUT STEP 5: (SEE FIGURE 5) o Assemble plastic grips (F) onto locking levers, To attach bumper to tractor: 1. Place flattened ends of bumper onto mounting brackets. Insert pin of locking lever into front hole in bumper and mounting bracket to support bumper on mounting bracket. 2. Insert pivot spacers (E) into rear holes in bumper. PUVOT SPACER (E)_ LOCKING LEVER J FIGURE 5 STEP 6: (SEE FIGURE 6) 3. Fasten locking lever and bumper to mounting bracket using a screw (A) or bolt (B), a lock washer (H) and a flat washer (G). Use screw (A) for LT tractors and bolt (B) for GT tractors. Assemble screw or bolt through pivot spacer in rear hole in bumper and into tractor frame. Tighten. Repeat for other side. NOTE: ff hole in (LT) tractor frame is not threaded, push in while turning screw (A) to create threads in hole. IMPORTANT: You must lower bumper before raising tractor hood. Pull out on locking levers and push bumper down as far as it will go. FLAT WASHER (G) LOCK ........... WASHER SCREW (A) or BOLT (B) AUGN THESE HOLES FIGURE 4 LEFT S_DE VIEW FIGURE 6 LEFT SIDE VIEW " For repair of major brand appliances in your own home... no matter who made it, no matter who soMdit! 1-800-4-MY-HOME sMAnytime day or night 1-8oo-4 9-4 63 To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center. ................ 1-800-488-1222 Anytime, dayornight For the replacement parts, accessories and owner's manuals that you _eed t_ doq_yourself, call Sears PartsDUreetSM! 1 800 366 PART 6a.m.-11p.m.CST, (1-800-366-7278} 7 days a week To purchase or 'nquire about t Sears Servbe Agreeme...

Descargar ahora

Introduzca dos números de la imagen: