Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Rotate valve 1/4 turn clockwise to shut fuel off. Rotate valve 1/4 turn counter-clockwise to turn fuel on. 4.11 Drive Wheel Release Lever: Located under the lower left rear corner of the engine deck (See Figure 4). The drive wheel release lever is used to release the hydrostatic drive system to allow machine to be pushed while the engine is not running. Rotate lever 1/8 turn counter-clockwise until caught under spring latch to release drive system. Pull spring latch out far enough to allow lever to rotate 1/8 turn clockwise to engage drive system. NOTE: Do Not tow machine or transmission damage may result. - 16 FIGURE 4 DRIVE WHEEL RELEASE LEVER 5. OPERATION INSTRUCTIONS 5.1 PRE-START 5.1.1 Fill fuel tank. For best results use only clean, fresh regular grade unleaded gasoline with an octane rating of 87 or higher. Regular grade leaded gasoline may also be used; however, combustion chamber and cylinder head will require more frequent service. See Engine Owner's Manual. Note: Fuel tank may appear loose at set-up, however, once fuel is added, tank will slowly expand to fit tank straps. Do not add oil to gasoline. Never fill the fuel tank so that the fuel level rises above a level that is 1/2” below the bottom of the filler neck to allow for fuel expansion and prevent fuel spillage. 5.1.2 Make sure you understand the controls, their locations, their functions, and their safety requirements. 5.1.3 Refer to the Maintenance Section, and perform all of the necessary inspection and maintenance steps. 5.2 MOWING 5.2.1 Starting Engine: Operator must be in the seat with the parking brake engaged and the PTO disengaged. Open fuel shut-off value. On a cold engine, place the throttle midway between the "SLOW" and "FAST" positions and place the choke in the "ON" position. On a warm engine, place the throttle midway between the "SLOW" and "FAST" positions and leave the choke in the "OFF" position. Turn ignition switch to "START" position. Release the switch as soon as the engine starts. After starting a cold engine, gradually return choke to the "OFF" position after engine warms up. IMPORTANT: Do not crank the engine continuously for more than ten (10) seconds at a time. If the engine does not start, allow a 60 second starter cool- down period between starting attempts. Failure to follow these guidelines can burn out the starter motor. 5.2.2 Stopping Engine: Bring unit to a full stop. Disengage the PTO and engage the park brake. Before stopping the engine, place the throttle control midway between the “slow” and “fast” positions. Allow the engine to run a minimum of 15 seconds; then stop the engine. - 17 Rotate ignition switch to “OFF” position. Remove the key to prevent children or other unauthorized persons from starting engine. Close fuel shut-off valve when machine will not be used for a few days, when transporting, and when the unit is parked inside a building. 5.2.3 Engaging PTO: DANGER POTENTIAL HAZARD . The rotating blades under the mower deck are dangerous. WHAT CAN HAPPEN . Blade contact can cause serious injury or kill you. HOW TO AVOID THE HAZARD . DO NOT put hands or feet under the mower or mower deck when the blades are engaged. DANGER POTENTIAL HAZARD . An uncovered discharge opening will allow objects to be thrown in an operator’s or bystander’s direction. Also, contact with the blade could occur. WHAT CAN HAPPEN . Thrown objects or blade contact can cause serious injury or death. HOW TO AVOID THE HAZARD . Never operate the mower with the discharge deflector raised, removed, or altered unless there is a grass collection system or mulch kit in place and working properly. The PTO switch engages the cutting blades. Be sure that all persons are clear of mower deck and discharge area before engaging the PTO. IMPORTANT: Operator must be in seat before the PTO can be engaged. Set throttle to "midway" position. The switch must be pulled out to the "ROTATE" position to engage the blades. Accelerate to full throttle to begin mowing. 5.2.4 Stopping PTO: Set throttle to “idle” position. Push in on the switch to the “STOP” position to stop the blades. 5.3 TRANSPORTING 5.3.1 Transporting a Unit: Use a heavy duty trailer to transport the machine. When the machine is on the trailer lower the cutting deck and fully extend the actuator. Never transport machine with mower deck supported by actuator, damage to the actuator or other components may occur. Engage the park brake and block the wheels. Securely fasten the machine to the trailer or truck with straps, chains, cables, or ropes. Be sure that the trailer or truck has all necessary lighting and marking as required by law. Secure to trailer with a safety chain. 5.3.2 Loading a Unit: Use caution when loading units on a trailer or truck. Use actuator to lift cutting deck off of the ground to provide more traction on the drive tires while loading the unit. One full width ramp that is wide enough to extend beyond the drive tires is recommended. If it is not possible to use one ...
Otros modelos de este manual:cortadoras de césped - FMD 524 (1.96 mb)