Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Personal bodily injury can result when these instructions are not followed. The information is for your safety and it is important! The safety decals below are on your product. If any decals are lost or damaged, replace them at once. See your local dealer for replacements. These labels are easily applied and will act as a constant visual reminder to you, and others who may use the equipment, to follow the safety instructions necessary for safe, effective operation. ATTACHMENT DECALS • Do not open cover with engine running. • Do not operate mower without thecomplete catcher in place • When operating on slopes, refer to operator's manual for counterweights. WARNING 1704405 • This shield must be in place at all times during operation. • Mower deflector must be in down position when blower is removed. 1717291 WARNING Decal - WARNING Do Not Open Cover Decal - WARNING Part Number 1704405 Part Number 1717291 Read and obey all operation and warning decals. TP 600-2562-01-AT-SMA 2 General Operating Instructions MOWING WITH THE CATCHER Always operate with throttle at full speed when mowing. Grass should be cut often, and not too short. If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width of the mower to prevent clogging. If grass is long, operate with mower in high cutting position for first pass, cutting again in a lower position on a second pass. Do not open the cover with mower engaged. If a large amount of cut grass is spilling out from under deck, the tube may be plugged or the bags may be full— discontinue mowing, stop the rider, disengage the PTO, shut off the engine and then empty the catcher or clear the tube. WARNING ALWAYS shut off the tractor. Disengage the PTO, and allow all moving parts to stop BEFORE disconnecting or clearing tube, or emptying catcher. Before leaving the operator’s position for any reason, engage the parking brake, disengage the PTO, stop the engine and remove the key. To reduce fire hazard, keep the engine, rider and mower free of grass, leaves and excess grease. Do not stop or park rider over dry leaves, grass or combustible materials. BEFORE OPERATION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important. For this reason, BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the underside of the catcher lid are free from grass and debris. Make sure that there is a snug fit between mower deck, blower housing, tubes, and grass catcher cover. REQUIRED ACCESSORIES A front-mounted weight carrier and 66 lbs. worth of weights are required when using this rear-mounted grass catcher. Never operate on slopes greater than 17.6% (10°). AFTER OPERATION Remove any debris from the the screen on the underside of the lid. Note: The lid screen can be partially removed for easier cleaning and should be cleaned regularly. The blower housing and tube should be removed for cleaning. Inspect the grass bags for wear or damage. Make sure that there is a snug fit between mower deck, blower housing, tubes, and grass catcher cover. STORING THE GRASS CATCHER CAUTION Do not leave grass in bagger containers. Empty containers after each use and before storing. Failure to do so may result in spontaneous combustion which could develop into a fire. Clean the grass catcher thoroughly using a mild detergent (other products may damage the tube). Remove any debris from the the screen on the underside of the lid. If paint has been scratched on metal parts, touch up with paint, or apply a thin film of oil to prevent corrosion. Store in a dry area. Dry thoroughly before storing for a long period of time. Always store away from moisture. 3 Initial Assembly & Installation INSTALL MOUNTING PLATES BROADMOOR / 1600 / 2600 / LT SERIES Install Plates & Spacers 1. Mount the side brackets (B, Figure 1) to both sides of the frame using the holes shown. Secure with one 3/8-16 x 1 capscrew (C) and 3/8-16 nylock nut (A) per side. 2. Install the rear spacers (C, Figure 2). Secure with two 1/2-13 x 2-1/2 capscrews (E), washers (D), spacers (C), and 1/2-13 nylock nuts (A) per side. Figure 1. Install Side Brackets A. Nylock Nut, 3/8-16 C. 3/8-16 x 1 B. Side Bracket A B C A C D D B Figure 2. Install Rear Spacers A. Nylock Nuts, 1/2-13 C. Spacers B. 1/2-13 x 2-1/2 Capscrew D. 1/2” Washers INSTALL MOUNTING SPACERS CONQUEST / 1700 / 2700 / YT & PRESTIGE / 1800 / 2800 / GT SERIES NOTE: If installing this catcher on a unit equipped with a rear tiller, refer to the “Installation with a Tiller” section for special installation instructions. Install Spacers 1. Install the rear spacers (C, Figure 3). Secure with two 1/2-13 x 2-1/2 capscrews (E), washers (D), spacers (C), and 1/...
Otros modelos de este manual:cortadoras de césped - 1694153 (621.49 kb)
cortadoras de césped - 1694693 (621.49 kb)