Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Route the brake cable below the lower handle. Place end of cable through the hole in the -bracket as shown in figure 3. Be careful not to bend or kink the cable at any time. Push the plastic fitting until it locks into the hole in the bracket. A WARNING: Brake cable must be assembled as shown for proper blade brake operation. 2. Hook the “Z” end of the brake cable into the hole in the blade control handle from the inside to the outside as shown in figure 3. SECURING THE CABLES (Hardware D) Secure the cables to the left side of the handle as follows. A WARNING: When attaching the control cables, the cables must be routed to avoid contact with all sharp edges and hot surfaces to prevent damage to the cables, which will render the controls inoperative. 1. Insert posts on cable ties into holes provided on the inside of the handle, one on the upper handle and two on the lower handle. The holes may be either on the inside -or outside of the handles. See figure 4A. 2. Secure the cable(s) with the cable ties. See figure 4B. 3. Trim excess ends of cable ties. ATTACHING THE STARTER ROPE (Hardware B) 1. The starter rope is inside the top of the engine. Additional rope may be wound around the starter handle. If so, unwind the rope from the handle. 2. With the spark plug wire disconnected and grounded, depress the blade control handle and pull the rope out of the engine. —3. Place the rope guide around the starter handle, so the rope guide is positioned as shown (bends downward slightly). Insert the rope guide into the handle, and secure with hex lock nut. INSTALLATION OF WHEELS (Hardware E) The three holes provide three cutting heights for your mower. Use the same hole location for all four wheels when assembling. If wheels are to be assembled in the lowest cutting position (highest hole in the deck), refer to the note below. If your mower has two sets of holes (see figure 6), the front wheels must be assembled in one of the three holes nearest the front of the deck. The rear wheels must be assembled in one of the three holes nearest the rear of the deck. -To assemble the wheels: (See figure 6) 1. Place axle bolt through wheel. 2. Place one smaller cupped washer on axle bolt, with the cupped side of washer toward the deck (away from wheel). 3. Secure wheel to deck with one larger cupped washer on the inside of the deck (cupped side against the deck) and hex nut. Tighten securely. 4. Assemble the other wheels in the same manner. NOTE: If the lowest cutting position (highest hole in the deck) is used, it is necessary to place the larger washer on the outside of the deck and the smaller washer on the inside. FIGURE 7. FINAL ASSEMBLY OF MOWER 1. The chute deflector on your mower is held in an upright position by a block for shipping purposes only. This shipping block must be removed and discarded before the -mower is put into operation. See figure 7. To remove the shipping block, move the spring-loaded chute toward the engine by pushing above the shipping block. Remove the block and carefully lower the chute into operating position, keeping fingers out of the way. 2. Make certain all nuts and bolts are tightened securely. CONTROLS The blade control handle is located on the upper handle of the mower. See figure 8. The blade control handle must be depressed in order to operate the unit. Release the blade control handle to stop the engine and blade. A WARNING: The blade will be rotating whenever the engine is running. THROTTLE CONTROL The throttle control is located on the left side of the upper handle or on the engine. It is used to regulate the engine speed. The engine should be started with the engine in the FAST or START position. A WARNING: The throttle control cannot be used to stop the engine. BLADE CONTROL HANDLE X A RECOIL STARTER The recoil starter handle is attached to the handle. See figure WARNING: This control mechanism is a safety 8. Stand behind the unit in the operating position to start the device. Never attempt to bypass its operations. unit. 7 I OPERATION TO REDUCE THE RISK OF INJURY, DO NOT OPERATE MOWER UNLESS REAR TRAILING SHIELD AND THIS GUARD OR ENTIRE GRASS CATCHER IS IN ITS PROPER PLACE. FIGURE 9. Keep hands and feet away from the chute area on cutting deck. See figure 9. The operation of any lawn mower can result in foreign objects being thrown into the eyes, which can esult in severe eye damage. Always w< ar safety glasses or eye shields. We recommend wide vision safety mask for over spectacles or standard safety glasses. GAS AND OIL FILL-UP Service the engine with gasoline and oil as inst ucted in the separate engine manual packed with your mower. Read instructions carefully. A WARNING: Never fill fuel tank indoc rs, with engine running or until the engine has been allowed to cool for at least two minu es after running. TO START ENGINE AND ENGAGE BLADE 1. Attach spark plug wire securely to spark pluij. 2. Move the throttle control lever to FA...
Otros modelos de este manual:cortadoras de césped - 111-050R304 (1.49 mb)