Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to prevent injury to yourself and others. Save this manual for future reference. The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields be fore starting your trac tor and while mow ing. We recommend a wide vision safety mask for over the spec tacles or stan dard safety glasses. WARNING Donot operatemower unless containerisproperlyissubjecttowearand detierioration.Checkbagfrequently. R eplace whencrackedordamaged.Useonlyarecommended replacementcontainer. WARNING Donot operatemower unlesscontainerisproperlyissubjecttowearand detierioration.Checkbagfrequently.Replacewhencrackedordamaged.Useonlyarecommended replacementcontainer. WARNING Donot operatemowerunlesscontainerisproperlyissubjecttowearand detierioration.Checkbagfrequently.Replacewhencrackedordamaged.Useonlyarecommended replacementcontainer. 02079 LOWER CHUTE ATTACHING STRAPS PARTS IDENTIFICATION UPPER CHUTE CHUTE LATCH DUMP BAG INDICATOR LOWER CHUTE GRASS CATCHER CONTAINERS COVER ASSEMBLY UNPACKING INSTRUCTIONS • Remove all parts and packing materials from carton. • Check carton contents against list. Be sure all parts are there. CARTON CONTENTS: (3) Container Tops (3) Container Bottoms (1) Upper Chute (1) Lower Chute (1) Support Assembly (1) Cover Assembly (2) Shoulder Bolts (1) Retainer Spring SUPPORT ASSEMBLY SHOULDER BOLTS TOOLS REQUIRED FOR ASSEMBLY (1) 9/16" Wrench RETAINER SPRING 5 2 MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY (See Fig. 2) NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting coverassembly to tractor. 1. Position cover assembly on ground behind tractor as shown. 2. Lift and rotate cover to align cover brackets with support assembly tubes. 3. Slide cover assembly down onto the support tubes. FIG. 2 02532 COVER ASSEMBLY SUPPORT ASSEMBLY ASSEMBLY 02530 02531 1 BAGGER SUPPORT ASSEMBLY (See Figs. 1A & 1B) 1. Remove and discard the upper bolt on both sides of the drawbar. Using the same holes, install the shoulder bolts supplied and tighten securely. DRAWBAR SHOULDER BOLTS SUPPORT ASSEMBLY RETAINER SPRING PIN FIG. 1A REMOVE AND DISCARD UPPER BOLTS AND INSTALL SHOULDER BOLTS SUPPLIED FIG. 1B 2. Align support assembly pin with hole in drawbar and hang assembly over the shoulder bolts. 3. Be sure support assembly is seated properly and secure with retainer spring supplied. 6 CONTAINER ASSEMBLY (See Fig. 3) 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for other containers. PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donotoperatemowerunlesscontainerisprope rlyissubjecttowearanddetierioration.Checkbagfrequ ently.Replacewhencrackedor damaged.Useonlyarecomme ndedreplacementcontainer. 02097 FIG. 3 3 02739 CONTAINER BOTTOM HALF CONTAINER TOP HALF WARNING Donotoperatemowerunless containeris properlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacement container. WARNING Donotoperatemowerunlesscontainerisproperlyis nstalled.Container is subjectto wearanddetierioration. Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. 02083 CONTAINER MOUNTING (See Fig. 4) 1. Install one container to left side fi rst with warning to outside of unit. Install another container to center position and one in right position. NOTE: Right con tain er should always over lap left con tain er at center supports. 2. Close cover and lock latch handles over center support tubes. 4 FIG. 4 COVER LATCH HANDLES CONTAINER WARNING CONTAINER HANDLE CONTAINER WARNING CENTER SUPPORT TUBES 7 02552 LOWER CHUTE (See Fig. 5) 1. Raise and hold defl ector shield in upright position. 2. Place slot in lower chute over tab on mower deck and position lower chute over deck opening as shown. 3. Hook rear latch into fl ange hole on back of mower deck. 4. Hook front latch into tab hole on front of mower deck. 5 CAUTION: Do not remove defl ector shield from mower. Raise and hold shield when attaching lower chute and allow it to rest on chute while in operation. REAR LATCH FRONT LATCH DEFLECTOR SHIELD FIG. 5 02101 UPPER CHUTE (See Figs. 6A & 6B) 1. Lower mower deck to its lowest cutting position. 2. Assemble upper chute by inserting curved end into hole in back ...
Otros modelos de este manual:cortadoras de césped - 178478 (865.34 kb)