Votos - 2, Puntuación media: 3.5 ( )

Fabricar: Husqvarna Tamaño del archivo: 1.5 mb Nombre del archivo: Idioma del manual:

-Never store the machine or fuel container inside where there is an open flame, such as a water heater. • Never run a machine inside a closed area. • Keep nuts and bolts, especially blade attachment bolts, tight and keep equipment in good condition. • Never tamper with safety devices. Check there proper operation regularly. CAUTION CAUTION CAUTION SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS • Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage. Allow machine to cool before storing. • Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting. • Never make adjustments or repairs with the engine running. • Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer’s recommended parts, when necessary. • Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them. • Check brake operation frequently. Adjust and service as shown in the Operator’s Manual. WARNING! WARNING! 7 UNPACKING INSTRUCTIONS • Remove all parts and packing materials from carton • Check carton contents against list. Be sure all parts are there. TOOLS REQUIRED ." Wrench (2) 9/16" Wrench (2) 7/16" Wrench (2) Ft/Lbs Torque Wrench Drill ." and 5/16" Drill Bits 9/16" Socket and Ratchet Standard Screwdriver PARTS IDENTIFICATION CONTAINER CONTENTS 2 - Soft bag containers 1 - Bag of Hardware 1 - Upper Chute 1 - Lower Chute 1 - Cover Assembly 1 - Mounting Hardware 1 - Weight COVER ASSEMBLY BAG CONTAINERS LOWER CHUTE NOTE: When right hand (RH) and left hand (LH. are mentioned in this manual, it means when you are seated on the mower in the operator’s position. CAUTION BEFORE ASSEMBLING GRASS CATCHER TO MOWER: • Set parking brake. • Place motion control levers in “NEUTRAL” position. • Turn ignition key “OFF” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug and place wire where it cannot come in contact with plug. UPPER CHUTE 8 ASSEMBLY Frame Bracket Hanger Cover Assembly 1INSTALL PLATE AND HANGER 2 MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY For ease of assembly, you may wish assistance from another person for mounting the cover assembly to mower. 1. Position cover assembly on the ground behind the mower. 2. Lift and rotate cover to align the frame bracket with the hanger and slide the cover down until secure. Remove plastic end cap from the center bag support arm. Fully insert spacer plugs into the ends of the support tube. It may be necessary to tap the spacer into place with a hammer or mallet. Replace the plastic end cap back over the spacer. The additional extension will hold the hood more securely when latched. 3 INSTALLING SPACER PLUG 1. Using hardware provided in kit, attach support mount to unit. 2. Attach hanger bracket to support mount. Do not fully tighten nuts at this time. 3. Secure rear end of support straps to outside of hanger assembly. Set reinforcement plates to the outside of the tank brackets and fasten front end of support strap to tank bracket and reinforcment plate with round head bolt. Secure front end of reinforcement plate to tank bracket with hex bolt. Fully secure all mounting hardware. See illustration. NOTE: Depending on model, rear guard hole may need to be drilled out to 5/16" if kit hardware is too large. Remove center end cap Insert spacer and replace cap Support Straps Reinforcement Plate Round Head Bolt Placement Hex Bolt Placement Hanger Bracket Support Mount 9 ASSEMBLY 4 CONTAINER INSTALLATION 1. Install containers on support frame, overlapping containers at center tube. Note: One container should always overlap the other container at the center tube. 2. Close cover and lock latch handle over support tubes. Support Frame Latch Handle WARNING! DO NOT operate mower unless container is properly installed. Container is subject to wear and deterioration, check containers frequently, replace when cracked or damaged. Use only a recommended replacement container. 1. Raise and hold deflector shield in upright position. 2. Fit lower chute as shown and hook rear latch to mower deck. 3. Align the bracket slot on lower chute with the deflector bracket tab on the mower deck. Slide chute down over tab. 4. With the lower chute in proper position, hold the chute securely while hooking the front latch to the mower deck. NOTE: While hooking the latches, the deflector shield may try to push the chute away from the mower deck opening. It is important to hold the chute in position while hooking the latches to the mower deck. 5LOWER CHUTE INSTALLATION Deflector Shield Deflector Bracket Tab Rear Latch Attach Rear Latch here Front Latch 10 ASSEMBLY NOTE: Depending on model, it may be necessary to drill a ." hole to move the upper chute latch nut. 1. Slide upper chute onto lower chute, lining up notches and channel...

Descargar ahora

Introduzca dos números de la imagen: