Votos - 5, Puntuación media: 3.2
(
)
)
|
Resumen del manual
2. With the other hand, SLOWLY push the blade control lever forward to the “ON” position. 3. Belt drive models—Move the gear shift lever to the desired speed. Always begin at a slow ground speed and increase only as the condition of the terrain warrants. To stop mowing, slowly and evenly squeeze up on both traction control levers until the mower comes to a complete stop and then with your thumbs, push down on the traction lever locks until the levers are securely locked in the neutral position. Return the gear shift lever to the neutral “N” position 4. Hydro drive models—Slowly, and evenly, engage the forward and reverse levers and begin mowing. To stop moving, ease up on the levers or simply let go of the mower. 5. To stop the blades, pull the blade control lever back to the “OFF” position. Warning—the blades may take up to 7 seconds to stop turning. The Soft Start feature is critical to maintaining belt, clutch, and engine life. NEVER “slam” the blade on/off handle from off to on without pausing an adequate time in the soft start range. DEK® is exclusively distributed by GXi International, LLC Rev: 8/2008 13 of 21 Heavy Duty Power Equipment Mowing and Floating Deck Instructions 36B, 36BX, 36H, 36HX, 52H, 52HX Changing the Height of Cut Your DEK mower is equipped with an easily adjustable floating deck which can be adjusted for cut heights of 1.” to 4.” in .” increments. Figure 6 How to Change the Cut Height 1. Hold one side of the deck by the black handle provided (Figure 7). Figure 7 2. Using your other hand, remove the retaining clip and pin from the two brackets on that side of the mower. (Figure 8). Figure 8 3. Raise or lower the deck until the hole in the height adjust bar (Figure 9A) aligns with the desired cut height hole on the height adjust bracket (Figure 9B). 4. Replace the height adjust pins into the desired cut height holes. All 4 height adjust pins must be set to the same desired cut height position. Figure 9A 5. Repeat the same adjustment process with the two height adjust pins / brackets on the other side of the mower deck. Removing the Blades Figure 9B CAUTION Beware of the cutting edges on the blades. The rotation of one blade may cause the other blade(s) to rotate. Always wear work gloves when handling blades. 1. Park the mower and level ground and block the rear wheels to prevent accidental rollback. 2. Raise the front end of the mower using a jack stand. 3. Using two 15/16” box end wrenches. Use one wrench to loosen nut “A” while holding bolt “C” with the other wrench. (Figure 10) 4. Slide the blade bolt down through the mower deck and out. 5. To reinstall, reinsert the blade bolt through the cutting deck. 6. Install the blade spacers that were removed, back onto the blade bolt followed by the nut and tighten. (Figure 10) IMPORTANT: The amount of spacers should always be the same on each blade bolt. Never put the spacers below the blade. A C Figure 10 DEK® is exclusively distributed by GXi International, LLC Rev: 8/2008 14 of 21 Heavy Duty Power Equipment 36B, 36BX, 36H, 36HX, 52H, 52HX General Maintenance Fuel Maintenance The Importance of Maintenance Good maintenance is essential for your DEK lawn mower for upkeep of safety and quality. To help you properly care for your lawn mower, the following pages include a maintenance schedule, routine inspection procedures, and simple maintenance procedures using basic hand tools. Maintenance is the responsibility of the owner and must be performed regularly. Other service tasks that are more difficult, or require special tools, are best handled by professionals and are normally performed by a DEK technician or other qualified mechanic. The maintenance schedule applies to normal operating conditions. If you operate your lawn mower under severe conditions, such as sustained prolonged use or high-temperature operations, or use it in unusually wet, dusty or rocky conditions, consult your servicing dealer for recommendations applicable to your individual needs and use. Please be sure to use genuine DEK mower replacement parts when servicing your mower to assure the best quality, safety and performance for your mower. WARNING DANGER: Before making any adjustments and/or servicing to your DEK Mower, make sure the mower is on level ground, blades disengaged, key removed, and the engine off with the spark plug wire(s) removed from the spark plug(s) to prevent accidental contact. If adjustment or maintenance is being performed after operation of the mower, allow the unit to cool since heat build up could cause severe burns. Maintenance Schedule Item Procedure Time Interval Break-in (first 5 hrs) Every 8 hrs (daily) Every 40 hrs (weekly) Every 100 hrs (Bi-weekly) Every 200 hrs (monthly) Belts Inspect (adjust if needed) X X Blades Inspect and Sharpen X Engine Air Filter Inspect (see Engine Owner’s Manual) X Engine Cooling Areas Clean (see Engine Owner’s Manual) X Engine Oil Check (see Engine Owner’s Manual) X Change (see Engine Owner’s Manual) X X Engin...
Otros modelos de este manual:cortadoras de césped - 36B (2.62 mb)
cortadoras de césped - 36BX (2.62 mb)
cortadoras de césped - 36H (2.62 mb)
cortadoras de césped - 52H (2.62 mb)