Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
• As the fluted knob is loosened the rear wheel wilt slide down. • Hold the Edger so that the top of the main frame is level with the top of the curb and retighten the fluted knob. • Turn the Edger so that the front wheel will be on the same surface as the right rear wheel. The left rear wheel is on top of the curb and the right rear wheel is supporting the Edger on the lower surface. • White standing on the right side of the Edger, loosen the T-knob on the front wheel bracket. • With your left hand, lift the front of the Edger using the T-knob until the main frame is again level with the top of the curb. • With your right hand, push the front wheel down until the wheel makes contact with the surface below. • HoLdthe front of the main frame level with your right hand and retighten the T- knob with your left hand. Check level of main frame to top of curb and make any adjustments. • Reconnect the spark plug wire and start the engine. The depth of cut adjustment is the same as described in Edging Operation paragraph, WARNING: Keep away from the rotating blade. The blade can cause injury. TO USE THE BEVEL CUT FEATURE Bevel edging reduces the need to edge as often creating a type of trench along your sidewalk, driveway and etc. Move the index lever to the bevel cut position and secure index lever in the slot. Prior to starting the engine, line the Edger up as if you were going to bevel cut and move the depth control lever down to test the blade location. Return the depth control lever to the .fOrward slot of the adjustment bracket to raise the blade. Start the engine and move the depth control lever to the desired depth of cut. BEFORE STARTING ENGINE PRE-USE CHECK OF CONTROLS All controls should be checked for proper function before servicing or starting the engine. • Move the depth control lever into all four positions in the selector plate. Make sure the depth control lever snaps irtt0._allffo.ur holes as shown in figure on page 6! ' • Return the depth control lever to the forward hole in the selector plate. FILL/ADD OIL: This Edger was shipped with a 20 ounce container of SAE30 motor oil. This oil must be added to the engine before operating. Remove the oil fill cap/dipstick and fill the crankcase to FULL line on dipstick, Your engine may not require the entire 20 ounces of oil. DO NOT OVERRLL. Tighten the fill cap/dipstick securely each time you check the oil level. ,_ OIL RECOMMENDATIONS _!'!_' Only use high quality detergent oil rated with API service classification SG, Select the oil's SAE viscosity grade according to your expected operating temperature: J -->>Warmer )> 32°F I : NOTE: Although multi-viscosity oils (5W30, 10W30, etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. TO ADD ENGINE OIL • Place the Edger on a level surface. • Remove the oil fill cap/dipstick as shown in next figure. • Fill the engine crankcase, pouring slowly. DO NOT OVERFILL. For approximate capacity see PRODUCT SPECIFICATIONS on page 11 of this manual. Reinstall the oil fill cap/dipstick and tighten securely. Wipe away excess oil. Check oil before each use. Add if needed. Fill Tube :ill Cap/ Dipstick Z_ CAUTION: Never fill the gas tank while the engine is running or hot. Immediately wipe off any spilled gasoline before attempting to start the engine. t k_'__ _, _ Fuel Fill Cap FILL GAS: Fill the fuel tank with clean, fresh, unleaded grade automotive gasoline. Be sure that the container you pour the gasoline from is clean and free from dust or other foreign particles. Never use gasoline that may be stale from long periods of storage in the container. Reinstall fuel cap. WARNING: Experience indicates that alcohol blended fuels (called gasohol or using methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain fuel tank, start engine and let it run until fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional informa tion. Never use engine or carburetor cleaner products in the fuel tank or perma nent damage may occur. ,/_ WARNING: Gasoline is flammable and caution must be used when handling or storing it. Do not fill fuel tank while Edger is running, hot, or when Edger is in an enclosed area. Keep away from open flame, electrical spark, and do not smoke while filling the fuel tank. Never fill fuel tank completely; but fill the tank to within 1!4-1/2 inch from the top to provide space for expansion of fuel. Always fill fuel tank outdoors and use a funnel or spout to prevent spilling. Make sure to wipe up any spilled fuel before starting the engine. Store gasoline in a clean, approved container, and kee...