Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Sears, Roebuck and Co. D/817 WA. Hoffman Estates, Chicago, IL 60179 The model number and serial numbers will be found on MODEL NUMBER: 486.24275 a decal attached to the base assembly. SERIAL NUMBER: You should record both the serial number and the date of purchase and keep in a safe place for future reference. DATE OF PURCHASE: Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. • This cab provides foul weather protection only. tt • The snow cab will restrict your field of vision in does not provide protection against exhaust fumes, some directions. Use extra caution when operating collision, rollover or other accidents. your tractor with the snow cab attached. • Read the snow cab and vehicle owner's manuals • Watch out for low tree limbs or other overhead and know how to operate your vehicle before using obstructions that may not previously have inter- the snow cab attachment. fered with operation of the tractor. The extra height • Be sure there is adequate ventilation when using of the snow cab may cause these objects to the tractor and snow cab in confined areas. become obstacles. • Check the area of operation thoroughly before using the tractor. _, Look for this symbol to point out important safety precautions. It mean--Attention!! Become alert!! Your safety is involved. 2 SHOWN FULL SIZE A B ,..........._7' y-_*:,;_'(_,-iA .............. \ ........... D \ / \ ........ \ \\\\ REF. QTY. DESCRIPTION REF. A 2 Carriage Bolt, 5/16 x 2" D B 4 Hex Bolt, 1/4 x 1-1/2" E C 4 Hex Lock Nut, 1/4" F G CARTON CONTENTS 1. Base Assembly 4. U-Tube 2. Top Tubes (2) 5. Support Rods (3) 3. Upright Tubes (2) 6. Front Brace Rod 7. Vinyl Canopy j.J- J 4 3 j- 2 jJ NOT QTY. 2 2 4 2 SHOWN FULL SIZE E G F DESCRIPTION Flat Washer, 5/16" Plug Rubber Pad Plastic Knob J J / t ,f/ / TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches (1) 1/2" or 9/16" Socket Wrench REMOVAL OF PARTS FROM CARTON • Remove all parts and hardware packages from the carton. Lay out all parts and hardware and identify. ASSEMBLING SNOW CAB Your tractor fender style may differ from the one shown in the drawings. These instructions apply to all fender styles. Raise the tractor seat, unscrew the seat spring bolts and remove the springs from the rear fender. See figure 1. \ '1 \'1 \1 BOLT /WASHER SPRING FIGURE 1 • Push the plastic plugs into the ends of the base assembly tubes. See figure 2. PLASTIC PLUG ( • Spread apart the slotted ends of the base assembly's front brackets just enough to fit them on the outside of the seat hinge bracket. Slide the slots over the bolt heads. See figure 3. IMPORTANT: The ends of the front brackets must fit snugly against the outside of the seat hinge bracket to keep the base assembly secured. • Align the assembly's bottom brackets over the holes where you removed the seat springs. Check to see if the base assembly's tubing rubs against the fender. If the tubing rubs, apply the adhesive pads to the fender, under the tubing. See figure 3. SEAT HINGE BRACKET FRONT BRACKET _- (BASE ASSEMBLY) FIGURE 3 Reassemble the seat springs on top of the base assembly's bottom brackets using the bolts and washers that you removed. Tighten securely, but do not to overtighten. See figure 4. BOLT WASHER _/SPRING FIGURE 2 FIGURE 4 4 Assembletheuprighttubestothebaseassembly usingtwo5/16-18x 2"carriagebolts(onoutside)andtwo5/16"flatwashersandplasticknobs(oninside). Seefigure5. ,/-J /' / / / \ J J iJ i iJ 5/16" x 2" PLASTIC i CARRIAGE BOLT KNOB / FLAT WASHER FIGURE 5 • Assemble the top tubes to the upright tubes using two 1/4" x 1-1/2" hex bolts (from outside) and two 1/4" hex lock nuts (inside). Do not tighten yet. See figure 6. • Fit the front U-tube onto the top tubes. Fasten the tubes together using two 1/4" x 1-1/2" hex bolts (on outside) and two 1/4" hex lock nuts (on inside). Tighten all loose bolts. See figure 6. • Fit the three support rods into the holes in the top tubes, with the rods arching upward. Do not over bend the rods when installing. See figure 6. 1/4" x 1-1/2" SUPPORT ROD FIGURE 6 Insert the ends of the front brace rod into the holes in the U-tube and then swing the bottom of the rod down to rest on top of the dash panel. On newer "GT" tractors, use the holes at each end of the U-tube. On older "GT" tractors and on "LT" tractors, the alternate holes in the front section of the U-tube may provide the best fit. See figure 7. FRONT BRACE ROD FIGURE 7 Raise the tractor's hood. Place the snow cab canopy onto the tubing frame, draping the front flap down in front of the tractor's dash panel. Lower the hood, trapping the front flap under the hood. Secure the sides of the canopy by fastening the elastic hooks to the bottom edge of the footrest and fender. Any levers or handles on snowthrowers or snow blades should be located outside of the cab. See figure 8. FRONT FLAP ELASTIC HOOK FIGURE 8 5 Readthis owner'smanualand...