Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Running the deck out of level will result in poor cut quality and increased belt wear. Fig. 2 Part No 510267 Form No F031607A 9 HW Owner’s Manual PROPULSION This unit is self-propelled, and is controlled by a lever control. To engage the wheel drive, pull up and squeeze it against operator's handle. The drive is disengaged by releasing this lever.(See Fig. 3 & 3.1) GROUND SPEED can be varied by selecting a higher or lower gear using the gearshift lever on top of the handle (See Fig. 4). Under most conditions cutting should be done in first or second gear. Third gear should be reserved for conditions where weeds and brush are thinned out or not as tall. The quality of the cut produced is directly related to the unit's ground speed during cutting. If the quality of the cut is not satisfactory (i.e. material left standing) you should shift into a lower gear during cutting. For improved control in confined areas, this machine can be pushed forward or backward by releasing the drive lever located at the right side of the handle. HILLSIDE MOWING WARNING! Never mow on any slope greater than 15 degrees. Always mow across the face of slopes; never up and down or diagonally see fig 5). DO NOT attempt sudden starts or stop when mowing on a slope. Avoid sudden turns and use extreme caution when changing direction on a slope. Fig. 3.1 Fig. 3 Fig. 4 Fig. 5 STORAGE Never store engine indoors or in enclosed poorly ventilated areas with fuel in tank, where fuel fumes may reach an open flame, spark or pilot light, as on a furnace, water heater, clothes dryer or other gas appliance. If engine is to be unused for 30 days or more, prepare as follows: Be sure engine is cool. Do not smoke. Remove all gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine. Drain fuel outdoors, into an approved container, away from open flame. Run engine until fuel tank is empty and engine runs out of gasoline. NOTE: Fuel stabilizer (such as Sta-Bil) is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow mix ratio found on stabilizer container. Run engine at least 10 min. after adding stabilizer to allow it to reach the carburetor. CAUTION: Wheels must be chocked or blocked when unit is parked on a slope. Part No 510267 Form No F031607A 10 HW Owner’s Manual MAINTENANCE PERIODIC MAINTENANCE Periodic maintenance should be performed at the following intervals: Maintenance Operation Every Use (daily) Every 5 hrs or (daily) Every 25 Hours Every 100 Hours Inspect for loose, worn or damaged parts. • Check for excessive vibration • Inspect belt for wear • Engine (See Engine Manual) Lubricate front wheels and height adjustment pins • Sharpen Blade • Replace blade and traction belts • BLADE Removal / Sharpening NOTE: When sharpening the blade it is a good idea to check the balance of the blade. A properly balanced blade will increase life of the bearings and other components. Tools required: 3/8 inch socket, 5/8 inch socket, torque wrench, blade block. 1. Disconnect spark plug wire. 2. Remove 5 screws (item 76) then remove belt guard (19). 3. Set the unit on its side to allow access to both pulley and the blade. Note: When tipping the unit on its side, keep the air cleaner side of engine up. Be sure the gas is drained out to prevent from spilling before tipping the unit on its side. Never tip the mower more than 90 degrees and do not leave the mower tipped for any length of time. 4. While protecting your hands with pair of gloves or heavy rag to hold the blade, loosen but do not remove the bolt (88) on the pulley side (fig. 6). 5. Remove jam nut (68), blade washer (43), blade (44), blade washer (43), and blade spacer (39). 6. Replace or sharpen the blade then install in the exact order they were removed (fig. 7). 7. Tighten the jam nut until it is flush with the end of the shaft (fig 7). Then tighten the bolt on the pulley side - Torque it to 80 ft-lbs. Note: When replacing the blade use B.G.I. Part no. 510107. 8. Reinstall belt guard then connect spark plug. Note: Before installing the fasteners inspect them for wear and replace as necessary. BELT REPLACEMENT When replacing one belt the other should be inspected for wear and replaced if worn. It is good practice to change both belts when either is worn beyond use. Use only original equipment belts for replacement. Billy Goat uses only premium quality, Kevlar corded and coated belts in your unit. Substitute belts do not meet the design and performance requirements for your unit, and will greatly reduce machine performance and belt life. Blade Drive Belt Tools required: 3/8 inch socket, 1/2 inch socket, 3/8" torque wrench. 1. Disconnect spark plug wire. 2. Set the deck height to middle position (3 inches cutting height). 3. Remove 5 screws (item 76) then remove belt guard (19). 4. Loosen but do not remove the nut (71) ...