Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
HARDWARE REFERENCE Tools Required for Assembly: * 7/16" wrench * 1/2" wrench * Flat Head Screwdriver * Hammer * Pair pliers L-1782-BH-01 3. Parts Reference Parts List L-1782-BH-01 4. REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 22 23 25 26 27 28 29 30 31 32 33 PART NO. B-983 B-1673P C-123 R-618 R-635-01 R-636 R-637-01 R-640 R-653 R-704 R-705-10 R-713-10 R-746 R-755-10 R-1503 R-1835-10 R-2466-10 R-2474-10 R-2473-10 R-775-10 R-803 10M0840P 11M1016P 30M1000P 40M1000P 45M1111P 45M1717P R-2469-01 R-2475-01 R-2476-10 QTY. 1 4 2 10 2 2 2 2 10 4 2 2 1 1 2 1 1 1 1 1 1 4 21 23 21 3 4 1 1 1 DESCRIPTION Hair pin cotter Hex Lock Nut, 1/4" Gauge wheel Reinforcing washer (special) Locking collar Push nut Axle Set screw (slotted), 5/16" Thatching Tine Nylon bearing, 1/2" Wheel support Bracket (tray mounting) Lift pin Tray Tine Safety wire Bracket (lift) Mounting frame Lift handle rear Lift lock bracket Handle retaining strap Handle grip Carriage bolt, 1/4" x 2-1/2" Carriage bolt, 5/16" x 1" Hex nut, 5/16" Lock Washer, 5/16" Plain Washer, 5/16" Plain Washer, 1/2" Rod, Small Rod, Large Handle Extention 5. L-1782-BH-01 EXPLODED REFERENCE 32 31 19 23 22 20 17 33 9 4 28 27 10 5 7 30 6 30 30 6 30 3 6 5 10 7 20 29 1 2 27 28 4 28 27 26 26 26 12 13 29 25 16 25 11 11 2 28 27 14 28 28 26 26 27 27 27 27 15 8 8 27 26 28 L-1782-BH-01 Step 1. Step 2. 6. 27 Hex Nut Qty. 4 26 5/16" x 1", Carriage Bolt Qty. 2 28 5/16" Lock Washer Qty. 4 2 Hex Lock Nut Qty. 4 25 1/4" x 2-1/2", Carriage Bolt Qty. 4 25 25 2 2 4 Reinforcing Washer Qty. 2 26 26 27 27 28 28 4 4 7. L-1782-BH-01 Step 3. Step 4. 27 Hex Nut Qty. 8 26 5/16" x 1", Carriage Bolt Qty. 8 28 5/16" Lock Washer Qty. 8 26 4 28 27 15 WARNING: Failure to install safety wires can result in personal injury ! if a tine should disengage from tine tray. 4 Reinforcing Washer Qty. 8 8. L-1782-BH-01 Step 5. Step 6. 27 Hex Nut Qty. 4 26 5/16" x 1", Carriage Bolt Qty. 2 28 5/16" Lock Washer Qty. 2 28 28 26 27 27 30 1/2" Flat Washer Qty. 4 6 Push Nut Qty. 2 30 6 7 3 9. L-1782-BH-01 Step 7. Step 8. 27 Hex Nut Qty. 4 26 5/16" x 1", Carriage Bolt Qty. 2 22 20 28 26 27 27 28 5/16" Lock Washer Qty. 2 5 Locking collar Qty. 2 10 1/2", Nylon Bearing Qty. 4 10 5 Step 9. 3" A 11/32" diameter hole needs to be drilled in right side of your tractor frame above front tire. Layout and drill the hole 3" from front of and center of frame lip. 8 10 8 5/16", Set Screw Qty. 2 10. L-1782-BH-01 Step 10. Step 11. 28 26 27 Assembly Lift Lock bracket assembly to tractor under frame where the hole was drilled in previous step. 28 26 27 1 29 13 27 Hex Nut 26 Qty. 1 5/16" x 1", Carriage Bolt Qty. 1 28 5/16" Lock Washer Qty. 1 27 Hex Nut Qty. 2 26 5/16" x 1", Carriage Bolt Qty. 2 28 5/16" Lock Washer Qty. 2 1 Hairpin Cotter 29 Qty. 1 5/16" Flat Washer Qty. 3 13 Lift Pin Qty. 1 Step 12. 3132 Remove existing mower deck mounting pin from front of tractor. Assemble the Large or Small rod depending on whether tractor is a Simplicity or Snapper. Secure using retaining ring previously removed. Step 12. 3132 Remove existing mower deck mounting pin from front of tractor. Assemble the Large or Small rod depending on whether tractor is a Simplicity or Snapper. Secure using retaining ring previously removed. Adjustment For most lawns, adjust the thatcher as follows: 1. Select a smooth flat surface such as a driveway, sidewalk, garage floor, etc. Attach the thatcher to the tractor according to the mounting instructions. Be sure both gauge wheels are directly under the wheel support. 2. Loosen the four nuts on the sides of the "L" shaped tray mounting brackets, and the gauge wheel set screws. Adjust the tine tray to place the tine tips approximately 1/2" above the flat surface when in free position and to touch the flat surface when pushed back. 3. Tighten all nuts and gauge wheels set screws. ! OPERATION Tine ACTION- Grass should be less than 3" tall for proper tine action. When in use, all tines on the De-thatcher should deflect back and "flip" the thatch forward as shown in illustraion. If the tines seem to drag without flipping forward, the tine tray is too low and should be raised. If all the tines stay in the free position, the tray should be lowered. Make adjustments as necessary, up or down, by no more than 1/4" each time, until proper results are achieved. ! MAINTENANCE The key to years of trouble-free service is to keep your Sweeper clean and dry. Occasionally check all moving parts for free movement and, if necessary, lubricate with oil. Should rust develop, sand lightly and then paint area with enamel. Periodically check all fasteners for tightness. L-1782-BH-0111. ...