Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
There may be instances or conditions where it is not possible to hide all of the recycled or mulched clippings. In order to achieve the best results, please read and follow the mulching tips listed below: 1. Set the engine speed control to the wide open or full setting. 2. Place the mower deck cut height selector in either the top or second notch. Never cut more than 3/4” to 1” off the grass at any one time. Attempting to cut more grass will result in the deck plugging and cause the engine to stall. 3. It may be necessary to cut the lawn twice to achieve acceptable mulching performance especially on first cuttings or if the lawn is heavily fertilized. 4. Do not attempt to cut grass when it is wet. Mulching performance will be very poor under wet grass conditions. 5. Maintain sharp bade(s) throughout the cutting season. This is very important. Optimal mulching performance cannot be obtained with a dull or nicked up blade. OPERATION INSTRUCTIONS MOWING WITH A MULCHING ATTACHMENT (continued): 6. Keep the underside of the mower deck clean. Remove all grass and dirt build-up from the underside of the pan, the baffles and deflectors after each use. 7. Alternate mower direction. This will evenly disperse the mulched grass clippings over the lawn for even fertilization. If the mulching quality of the mower does not seem to be satisfactory, try one or more of the following tips: 1. Raise the height-of-cut setting on your mower. 2. It may be necessary to cut your grass more frequently. 3. Operate the mower at a slower ground speed. 4. Overlap cutting swaths instead of cutting a full swath with each pass. 5. Mow across the marginal areas a second time. 6. CUT HIGH - MOW OFTEN! CARE AND MAINTENANCE CAUTION Before performing any maintenance, turn off engine, allow to cool & remove key. Use extreme care when working on machinery. Do not wear watch or jewelry. Do not wear loose fitting clothes, and observe all common safety practices with tools. MAINTENANCE SCHEDULE •Check deck drive belt...........................................after 20 hours break-in •Check crankcase oil level.........................................................before each use •Clean grass & debris from muffler & manifold area...................before each use •Check air intake screen..............................................................after each use •Clean grass under deck..............................................................after each use •Check tire pressure.....................................................................every 10 hours •Inspect blades for sharpness........................................................every 10 hours •Clean air filter element................................................................every 25 hours •Grease all zerks..........................................................................every 50 hours •Check all belts............................................................................every 50 hours •Change engine crankcase oil............................(5 hours break-in) every 50 hours •Change engine oil filter..............................................................every 50 hours •Replace air filter element..........................................annually or every 100 hours CARE AND MAINTENANCE ENGINE: For complete maintenance and operating information of the engine, please refer to the maintenance instructions furnished by the engine manufacturer and included in your Zero Turn Radius mower information packet. Battery contains sulfuric acid electrolyte CAUTION which is poisonous and corrosive. BATTERY: •This is a maintenance-free battery and the fluid level cannot be checked. •Charge battery if required. OFF SEASON BATTERY STORAGE: •DO NOT remove battery from mower. •Clean top of battery and terminals with baking soda and water. •Identify each cable so they can be reconnected to the correct terminal. •Disconnect cables from terminals. ALWAYS disconnect ground cable first and reconnect last. •Charge battery. CARE AND MAINTENANCE CUTTER BLADE MAINTENANCE: CAUTION Stop engine and remove ignition key for safety. Wear heavy, thick gloves when holding onto cutter blade, avoid the sharp edge of the blade. Check sharpness of mower blades after every 10 hours of operation. Observe proper blade position prior to removal. 1. Safely raise front of mower. 2. Hold or block blade from turning. 3. Loosen blade bolt and remove blade. 4. When replacing blade, tighten blade bolt securely. Refer to diagram. Be sure blade iscentered on pilot before tightening bolt to 60 ft. lbs. Blades should be discarded when worn excessively. DANGEROUS! DO NOT USE BLADE IN THIS CONDITION! New Blade When notch starts, discard blade CARE AND MAINTENANCE TIRES: Correct tire pressure is essential for efficient operation of the mower. Check tire pressure periodically. Inflate tires to the pressure listed below. Front tires 9 x 3.50-4 16-21 lbs. Rear tires 16 x 6.50-8 8-14 lbs. Lug nuts or lug bolts should be ch...