Iniciar sesión:
Votos - 3, Puntuación media: 3.7 ( )

Manual de usuario Poulan, modelo 532182124

Fabricar: Poulan
Tamaño del archivo: 1.2 mb
Nombre del archivo: NOUS2003_532182124.pdf
Idioma del manual:enfr
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key. • Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. 6 1REAR MOUNTING BRACKET (See Figs. 1A, 1B&1C) NOTE: If your tractor already has four (4) shoulder bolts installed on the rear drawbar, simply hang the mounting bracket, lanced tabs towards bottom, on the bolts. Discard hardware group "A“ and disregard the remaining Step 1 instructions. FIG. 1A If your tractor does not have four (4) shoulder bolts installed on the drawbar, follow the instructions below. Use Hardware - - GROUP "A" Only one set of hardware in GROUP "A" will be used to mount the rear mounting bracket. To determine which set is correct for your tractor, check to see if there are (2) two upper corner ribs on each side of drawbar, if your tractor has the upper corner ribs, use the (4) four self tapping shoulder bolts. If your tractor does not have the corner ribs, use the set of (4) four bolts and locknuts. SELFTAPPING SHOULDER BOLTS (See Fig. 1B) 1. Using the four formed holes in the drawbar, install the four shoulder bolts as shown and tighten securely. 2. Hang the mounting bracket, lanced tabs towards bottom, on the bolts. BOLTS AND LOCKNUTS (See Fig. 1C) 1. Assemble the mounting bracket, lanced tabs towards bottom, using the four smaller inside holes on the drawbar. 2. Install the four bolts and locknuts as shown and tighten securely. BOLTS 2 COVER SEAL (See Fig. 2) No hardware required 1. Align mark on seal with mark at cover opening. 2. Work seal into opening so cover sits between flanges of seal. 3 SUPPORT POST (See Fig. 3) Use Hardware - - GROUP "B" CAUTION: Container support is spring A loaded and locked to the cover. Handle cover assembly carefully so as not to unlatch the cover from the container support. 1. Rotate cover assembly onto its side as shown. 2. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. 7 4 MOUNTING COVER ASSEMBLY TO TRACTOR (See Fig. 4) Use Hardware - - GROUP "C" NOTE: For ease of assembly, you may wish to obtain the assistance of another person for mounting assembly to tractor. 1. Raise seat on tractor to allow assembly to be mounted. 2. With cover closed, lift assembly and place support post inside mounting bracket. Allow assembly to rest on lanced tabs of mounting bracket 3. Line up holes in mounting bracket with holes in support post and insert bracket support pin. Secure with retainer spring. 4. Unlatch and open cover. 5. Install the three (3) tubing end caps onto container support 6. Tap each end cap onto container support tubes to seat securely. FIG. 4 5 CONTAINER ASSEMBLY (See Fig. 5) No hardware required 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUSTOVERLAPTO FORM SEAL AS SHOWN IN INSET. FIG. 5 ASSEMBLY CHECK: Squeeze sides of lower half of container and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. 8 6 CONTAINER MOUNTING (See Fig. 6) No hardware required 1. Install one container to left side first with warning to outside of unit. Install other container to right side. NOTE: Right container should always overlap left container at center support. 2. Close cover and lock latch handle over center support tube. COVER LATCH HANDLE CONTAINER WARNING CONTAINER HANDLE CENTER SUPPORT TUBE CONTAINER WARNING FIG. 6 DEFLECTOR SHIELD 1. 2. 3. 4. 5. 6. LOWER CHUTE (See Figs. 7A & 7B) Use Hardware - - GROUP "D" Press weld nut into rubber latch and install two latch hook assemblies to lower chute using screw, flat washer, and lock washer as shown. Tighten hardware securely. Raise and hold deflector shield in upright position. Place front of chute over front of mower deck opening and slide into place as shown. Hook front latch down into latch hole at front of mower deck. Hook rear latch down into latch hole at back of mower deck. CAUTION: Do not remove discharge guard from mower. Raise and hold guard when attaching lower chute and allow it to rest on chute while in operation. WASHER LOCK WASHER LATCH WELD NUT LATCH WELD NUT LOCK WASHER WASHER FIG. 7A LATCH HOOKS FIG. 7B 9 8 1. 2. 3. CHUTE LATCH ASSEMBLY (See Fig. 8) Use Hardware - - GROUPS "E & F" Assemble latch pin to upper chute, as shown. Press weld nut into rubber latch and assemble rubber latch to lower chute, as shown. Tighten all hardware securely. #10 x 1-1/8" SCREW UPPER CHUTE WASHERS 3/16 x 3/4 x 16 Ga. SPLIT SPACER #10x5/8” SCREW LOWER CHUTE ACORN NUT RUBBER LA...

Otros modelos de este manual:
cortadoras de césped - 964 77 50-00 (1.2 mb)
cortadoras de césped - CES36A (1.2 mb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría