Votos - 5, Puntuación media: 4.4
(
)
)
|
Resumen del manual
5. Press and hold the lock-off button (G) on the switchbox, then squeeze one of the Start/Stop levers towards the upper handle (H). 6. Continue to squeeze the start/stop lever towards the upper handle and release the lock-off button. 7. When the product has reached full speed gently lower it onto the lawn. • NOTE There are two start/stop levers fitted. Either one can be used for starting the product. • IMPORTANT Do not use the start/stop levers intermittently Stopping 1. To prevent a ring being cut in your lawn, tilt your product slightly (F). 2. Release the pressure on the Start/Stop lever. 1 B lock-off button bolt washer handle knob nut D F G H E 1 Adjusting the Cutting Height L M 1 2 3 3 2 1 HIGHEST This symbol visible LOWEST This symbol visible J K • THERE ARE 2 CUTTING HEIGHTS (J & K) • Height of cut is adjusted by turning over the cutting head. • Disconnect from the mains electricity supply and wait until the cutting head has stopped rotating. Turn your product upside down. • To Remove the Cutting Head and Fan (L) Hold the fan firmly and twist the cutting head anticlockwise as illustrated. Hold the cutting head in the centre and remove as illustrated. Hold fan in the centre and remove as illustrated. • Inspect for damage and clean as necessary before replacing the fan and the cutting head. • To Refit the Fan and the Cutting Head (M) Replace the fan as illustrated. Replace the cutting head, adjusting the height of cut as required. Hold the fan firmly and twist the cutting head clockwise, as illustrated. • IMPORTANT ENSURE FAN AND CUTTING HEAD ARE CORRECTLY LOCATED 1. Start at the edge of the lawn nearest to the power point so the cable is laid out on the lawn you have already cut. (N) 2. Cut your grass twice a week during the growing season, your lawn will suffer if more than a third of its length is cut at one time. Do Not Overload Your Product Using in long thick grass may cause the motor speed to drop, you will hear a change in the motor sound. If the motor speed drops you may overload your product which may cause damage. When using in long thick grass a first cut with the cutting height set higher will help reduce the load. See Adjusting the Cutting Height. How to Use N Grassbox • Always handle the plastic cutters with care - sharp edges could cause injury. USE GLOVES. Checking your Cutting System (R) • The cutting system must be kept in good condition and inspected before and after use. • Disconnect from the mains electricity supply and wait until the cutting head has stopped rotating. Turn your product upside down. 1. Visually check cutting head for wear. Replace if damaged. 2. Visually check plastic cutters for wear and replace when necessary. 3. Plastic cutters should be straight. Replace if bent or twisted. Replacing Plastic cutters (S) • Use only genuine Flymo replacement plastic cutters specified for this product. These are available from all Husqvarna Outdoor Products Service Centres and major retail outlets. • Plastic cutters must be replaced in pairs to retain balance. • Two plastic cutters of the same type should be fitted. • Never fit a metal bar blade to this product. To Replace Plastic Cutters • Disconnect from the mains electricity supply and wait until the cutting head has stopped rotating. Turn your product upside down. 1. Push plastic cutter towards centre of cutting disc. Lift plastic cutter away from cutting head. (T) 2. If the plastic cutter is broken during use - lever cutter out of the slot, and dispose of carefully. 3. Fit new plastic cutters into the slots at each side of the cutting head and pull into place. (V) • IMPORTANT ENSURE PLASTIC CUTTERS ARE CORRECTLY LOCATED. R S T V cutting head plastic cutters hood fan Cutting System Maintenance • For optimum performance your product is designed to be used with the grassbox fitted. Grassbox full Indicator (P) • IMPORTANT The machine must be switched on for the grassbox full indicator to operate. 1. When the ball reaches the top of the indicator window, it is time to empty the grassbox. See figure N. 2. When the ball is NOT visible in the indicator window, grass is being collected. See figure N. Emptying the Grassbox (Q) • Stop the product and wait until the cutting head has stopped rotating before emptying the grassbox. 1. Remove the grassbox lid. 2. Lift the grassbox off the product and empty. 3. Replace grassbox and lid carefully. • Failure to fit the grassbox and lid correctly will cause poor collection of grass clippings. P Q grassbox is full grassbox is empty Fails to Operate 1. Is the Power Turned On? 2. Check the fuse in the plug, if blown replace. 3. Fuse continues to blow? Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. Poor Flotation 1. Disconnect from the mains electricity supply. 2. Clean the underside of the hood and the fan blades. 3. Raise to a higher height of cut. See Adjusting the Cutting Height. 4. If poor flotation persists? Disconnect from the mains ...
Otros modelos de este manual:Gazonouborschiki - Hover Vac HV280 (1.01 mb)