Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
This new blower is equipped with the following features. See Figures 1a and 1b. MOTOR The blower has a powerful 30cc engine with sufficient power to handle tough blowing and vacuuming jobs. THROTTLE TRIGGER The blower can be operated at any speed between idle and full throttle. CRUISE CONTROL / THROTTLE LOCK The Cruise control (throttle lock) feature allows the user to operate the blower without holding the throttle trigger.To stop the engine, simply push the Cruise control knob after the engine has returned to idle speed. BLOWER TUBE AND NOZZLE The blower tubes can be assembled and installed on the blower using no tools. WIDE SWEEPER NOZZLE The wide sweeper nozzle allows for more area to be covered during blower operation. HIGH VELOCITY NOZZLE The high velocity nozzle is great for wet sticky leaves. It allows you to scrape wet leaves or debris while operating the blower. VACUUM The blower will covert to a powerful vacuum/mulcher using no tools. VACUUM BAG The vacuum bag attaches to the blower easily using the vacuum bag adaptor. VACUUM TUBES The vacuum tubes can be installed on the blower without using any tools. MULCHER The blower is equipped with a mulcher feature that efficiently reduces leaves at a 12:1 ratio. Page 7 Fig. 1a UPPER HANDLE UPPER BLOWER TUBE WIDE SWEEPER NOZZLE INLET COVER DOOR CRUISE CONTROL KNOB (THROTTLE LOCK) THROTTLE TRIGGER DOOR KNOB HIGH VELOCITY NOZZLE WET LEAF SCRAPER TUBE CLAMP Page 8 FEATURES INSTRUCTIONS When unpacking the blower: ¦ Carefully remove the blower and accessories from the box. ¦ Make sure that all items listed in the packing list are included. ¦ Inspect the blower carefully to make sure no breakage or damage occurred during shipping. ¦ Do not discard the packing material until you have carefully inspected and satisfactorily operated the blower. ¦ If any parts are damaged or missing, please call 1-800-242-4672 for assistance. WARNING: If any parts are missing do not operate the blower until the missing parts are replaced. Failure to do so could result in possible serious personal injury. PACKING LIST Blower Upper Blower Tube Wide Sweeper Nozzle High Velocity Nozzle Upper and Lower Vacuum Tubes Vacuum Bag Vacuum Bag Adaptor Tube Clamp 2-Cycle Engine Oil Operator's Manual NOTE: Read and remove all hang tags and store with your operator's manual. Fig. 1b PRIMER BULB CHOKE LEVER STARTER GRIP UPPER VACUUM TUBE VACUUM BAG LOWER VACUUM TUBE VACUUM BAG ADAPTOR VACUUM BAG SHOULDER STRAP TUBE CLAMP LOWER HANDLE ASSEMBL Y WARNING: Stop the engine and disconnect the spark plug wire before installing parts, making adjustments, cleaning, or when not in use. Failure to do so could result in possible serious personal injury. ASSEMBLING THE BLOWER TUBES See Figure 2. 1. Screw the nozzle onto the upper blower tube and tighten securely. Check tightness after initial run and retighten if needed. 2. Place clamp around the neck of the blower housing outlet. Do not tighten the wing nut yet. 3. Align the locking tab on upper blower tube with the slot in the blower housing outlet; push the tube into the housing. Twist to lock into place. 4. Rotate the tube so the nozzle is pointing upward as shown. Tighten the wing nut securely. 5. To remove the tubes, loosen the wing nut on the clamp. Rotate the tubes to unlock them remove from the blower housing outlet. INSTALLING THE VACUUM BAG See Figures 3 and 4. 1. Remove the nozzle and upper blower tube from the blower. 2. Unzip the vacuum bag and place the adaptor inside as shown. 3. Align the locking tab on the bag adapter with the slot in the blower housing outlet; push the bag adaptor into the housing. Twist to lock into place. 4. Tighten the wing nut securely. 5. Rotate the vacuum bag until the shoulder strap is upright. 6. Make sure the vacuum bag is zipped and closed before Fig. 3 Fig. 2 Fig. 4 ADAPTOR VACUUM BAG NOZZLE UPPER TUBE starting the unit. Page 9 ASSEMBLY INLET COVER DOOR DOOR KNOB WARNING: Stop the engine and disconnect the spark plug wire before installing parts, making adjustments, cleaning, or when not in use. Failure to do so could result in possible serious personal injury. INSTALLING THE VACUUM TUBES See Figures 5 and 6. To install the vacuum tubes: 1. Screw the upper and lower vacuum tubes together and tighten securely. 2. Loosen the door knob on the inlet cover door and open. Place the notch in the support arm of the upper vacuum tube under the hinge of the inlet cover door. 3. Push the upper vacuum tube into the blower housing. 4. Align the upper vacuum tube knob with the hole in the housing and tighten securely. To remove the vacuum tubes: 1. Loosen the upper vacuum tube knob. 2. Remove the vacuum tubes from the blower housing. 3. Close the inlet cover door and tighten the door knob securely. Fig. 6 Fig. 5 NOTCH IN SUPPORT ARM HINGE UPPER VACUUM TUBE KNOB Page 10 OPERATION WARNING: Gasoline is extremely flammable and explosive. A fire or explosion from gasoline will burn you and others. MIXING THE FUEL This product is pow...
Otros modelos de este manual:Gazonouborschiki - VAC ATTACK II UT08540 (794.21 kb)