Votos - 2, Puntuación media: 3.5 ( )

Fabricar: MTD Tamaño del archivo: 889.13 kb Nombre del archivo: Idioma del manual:

READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE \OUR POWER VACUUM. FAILURE TO COMPLY WITH THESE INSTRUC- Æj TIONS MAY RESULT IN PERSONAL INJURY. WHE N YOU SEE THIS SYMBOL- ^ HEED ITS WARNING. A Your power vacuum was suilt to be operated according to the rules for safe operation in this manu- DANGER: al. As with any type of po ver equipment, carelessness or error on the part of the operator can result in serious injury. If you vi< »late any of these rules, you may cause serious injury to yourself or others. 1. Read this operating and service instruction manual carefull'. Be thoroughly familiar with the controls and proper use of the po /ver vacuum. 2. Never allow children to operate this power vaccum. 3. Keep the area of operation clear of all persons, particul irly small children and pets. 4. Check fuel before starting engine. Do not fill fuel tank indc ars, when engine is running, or while engine is hot. Wipe off any s billed fuel before starting engine. 5. Do not change engine governor settings. 6. Do not put hands near rotating parts for any reason. 7. If the power vacuum should start to vibrate abnormally stop the engine and check immediately for the cause. Vibration is g snerally a warning of trouble. 8. Before cleaning, repairing or inspecting, make certain ell moving parts have come to a complete stop. Disconnect spark plui i wire and keep wire away from plug to prevent accidental starting. \lso keep throttle control lever in the stop position. 9. If the power vacuum should become blocked with debris at any point, shut engine off and wait until the impeller comes to a com )lete stop before attempting to remove the obstruction. Disconnect s park plug wire to prevent accidental starting. 10. Check all bolts for tightness at frequent periods. 11. Never store this power vacuum with fuel in the tank. Allow engine to cool before storing in any enclosure. 12. Keep bag and equipment free of debris when not in use. 13. Never operate this power vacuum unless air duct and vacuum bag are properly affixed in their places. Large zippered end of bag must be closed when operating to prevent objects from being blown out. 14. Never empty vacuum bag when engine is running. 15. Never change auxiliary hose attachment when engine is running. 16. The manufacturer recommends that the operator wear safety glasses or some other suitable eye protection when operating this machine. 17. Check the vacuum bag frequently for wear and replace when necessary. 18. Never operate as a leaf blower unless deflector assembly (optional equipment) is properly affixed in its place. 19. Exercise caution whenever operating as a leaf blower. Do not allow discharge to be pointed in the direction of persons. 20. No one should operate this unit while intoxicated or while taking medication that impairs the senses or reactions. CONTENTS OF HARDWARE PACK Hardware pack may contain extra ite ns which are not used on your unit. Hardware is shown approximately one-half size. Quantities of parts and part numbers are shown in parentheses. ATTACHING THE LOWER HANDLE Hex Bolts -3/8-16 x 1-1/2" Long (710-0344) -Lock Washers 3/8" I.D. (736-0169) Hex Nuts 3/8-16 Thread (712-0798) Hex Bolts -3/8-16 x 3/4" Long (710-0201) Cupped Washers 3/8" I.D. -0331) B ATTACHING THE REAR WHEELS I_I Wheel Spacers «—1/2" I.D. (750-0588) Flat Washers 1/2" I.D. x1" O.D. (736-0272) Push Caps (726-0128) ©©©© ATTACHING THE UPPER HANDLE CCP trri QZP CET) Hex Bolts 1/4-20 x 1-3/4" Long »-(710-0136) Hex Lock Nuts 1/4-20 Thread (712-0107) ATTACHING THE AIR DUCT ASSEMBLY Hand Knob (720-0170) Cupped Washer 5/16" I.D.—W Q (736-0242) v ATTACHING THE BAG -Stud Pins (711-0737) y'-v Push-On —Speed Nuts XCZ(1539-019) I i I i I i I i I i I i I i I i I i I i I i I i I FIGURE 1. 0 INCHES ASSEMBLY INSTRUCTIONS \ IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, service engine with gasoline and oil as instructed in the separate engine manual packed with your unit. Upper Handle >v. Hex Bolt 3/4" . ,L?*?9 u Hex Bolt 1-1/2"' Lock Washer L Hex Nut Cupped Washer,, FIGURE 2. HSXNUt FIGURE 3. Axle-1 Shaft Flat Washer NOTE: Reference to right or left hand side of the vacuum is observed from behind the unit in the operating position. TOOLS REQUIRED FOR ASSEMBLY (2) 9/16“ Wrenches (2) 7/16" Wrenches (1) Hammer or Rubber Mallet UNPACKING Remove the vacuum, loose parts, hardware pack and literature from the carton. Make certain all parts and literature have been removed before the carton is discarded. -LOOSE PARTS IN CARTON (See figure 1) (1) Upper Handle (1) Lower Handle (1) Air Duct Assembly (2) Rear Wheels (1) Bag ATTACHING THE LOWER HANDLE (Hardware A) 1. Raise the back of the unit off the floor approximately 3 inches and block it so that the lower handle and rear wheels may be assembled. 2. Place lower handle in position on the vacuum, lining up the holes in the handle with the holes...

Descargar ahora

Introduzca dos números de la imagen: