Votos - 5, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Remove the batteries from your unit when you do not expect to use the unit for several months. Stored data is not lost when batteries are removed. MOSDCD m croSD card slot (w th m croSD card n pos t on for nsert on) To install the microSD card: 1. Remove the battery cover by turning the D-ring 1/4 turn counter-clockwise and pulling the cover loose. 2. Locate the microSD card in the slot below the batteries and press down on the top edge of the card until you feel it click. Then gently allow the card to release. 3. Press down again to install the card, making certain the card is fully in place to prevent damage when reinstalling the battery cover. To install the lanyard: 1. Place the loop of the lanyard throught the slot at the base of the unit. 2. Route the strap through the loop, and pull tight. Install the carry lanyard n the slot at the bottom of the un t GPSMAP 76Cx Owner’s Manual GettInG Started Using the GPSMAP 76Cx Keypad IN/OUT Zoom Keys ROCKER Key Press and hold to turn the unit on or off. ENTER/MARK Key Press to zoom in or out on the Map Press up, down, left, or right to highlight page. options and to enter data, or move the map panning arrow. Press to scroll up or down a list on any other page. PAGE Key FIND/MOB Key Press to cycle through the main pages. Press at any time to view the Find Menu. MENU Key Press and hold for MOB. POWER Key Press to view page options. Press twice to view the Main Menu. Press and Release to adjust the Press and release to enter highlighted backlighting. options, data or confirm on-screen messages. QUIT Key Press and hold at any time to mark your Press to cancel data entry or exit a current location as a waypoint. page. GPSMAP 76Cx Owner’s Manual GettInG Started Turning on the GPSMAP 76Cx To turn the GPSMAP 76Cx on and off: Press and hold the POWER. Adjusting the Backlight To adjust the backlight level: 1. Press and quickly release the POWER key. 2. Press up on the ROCKER to increase the brightness, or press down to decrease. 3. Press ENTER or QUIT to close. See page 34 for information on changing the screen colors and backlight time out and brightness levels. Initializing the GPS Receiver The first time you turn on your unit, the GPS receiver must collect satellite data and establish its current location. To receive satellite signals, you should be outdoors and have a clear view of the sky. To initialize your GPSMAP 76Cx: Hold the unit in front of you facing the sky and observe the Satellite page. While the GPS receiver is searching for the satellite signals, a “Locating Satellites” message is replaced by an “Acquiring Satellites” message until a location fix is made. The outer c rcle represents Head ng bugthe hor zon. nd cates your The nner d rect on c rcle s 5 degrees from The Strength ofthe hor zon. each satell te s gnal. Initialization Options If the unit cannot get a satellite fix, an options menu with a list of solutions appears. Highlight the appropriate solution and press ENTER. GPSMAP 76Cx Owner’s Manual GettInG Started Using the Status Bar At the top of each page, the status bar provides status information for several unit features. Status Bar The Battery Power icon ( ) shows the remaining battery power. The Auxiliary Power icon ( ) or Cable Connection icon ( ) appears when the unit is plugged in to an external or USB power source. Satellite signal status is shown when searching for or acquiring satellites ( 3D fix ( ), when a 2D fix( ) is attained and when a ) is attained. The Backlight icon ( ) appears when the backlight is on. The Backlight is off when you turn the unit on. The Backlight uses a significant amount of battery power. On-Screen Messages When a significant event in the operation of the unit occurs, an on-screen message appears to advise you of the occurrence. In each case the condition is described and often a remedy provided. Press ENTER to acknowledge the message and close the window. On-Screen Messages GPSMAP 76Cx Owner’s Manual 5 GettInG Started Using the Databases Optional MapSource CD-ROMs enhance the versatility of your GPSMAP 76Cx. This data is loaded to the microSD Card already installed in the unit. With optional MapSource City Navigator data, you can view listings of nearby restaurants, lodging, shopping centers, attractions and entertainment, and even retrieve addresses and phone numbers for any listed location. The included USB Interface Cable or an optional PC interface cable (with a serial connector) can be used to transfer MapSource CD-ROM data to the microSD card. Higher capacity and pre-loaded microSD map data cards are also available. Map data transfer requires the USB Interface Cable provided with the unit to transfer MapSource data from a PC to the microSD card when installed in the GPSMAP 76Cx. Use the USB Mass Storage feature to transfer other files to the microSD as explained on page 35. See for compatible MapSource products. MOSDAD m croSD card slot located n battery compartment USB n...
Otros modelos de este manual:navegadores GPS y receptores - GPSMAP 20072009 (1.03 mb)