Votos - 5, Puntuación media: 3.6 ( )

Fabricar: Genie Tamaño del archivo: 696.71 kb Nombre del archivo: Idioma del manual:

Do not fill to maximum level until the battery charge cycle is complete. Overfilling can cause the battery acid to overflow during charging. Neutralize battery acid spills with baking soda and water. 3 Install the battery vent caps. 4 Charge the battery. 5 Check the battery acid level when the charging cycle is complete. Replenish with distilled water to the bottom of the fill tube. Do not overfill. 16 Genie Lift Part No. 35566 First Edition • Sixth Printing Operator's Manual Transport Instructions Observe and Obey: Be sure the vehicle capacity and loading surfaces are sufficient to support the machine weight. See the serial plate for the machine weight. The transport vehicle must be parked on a level surface. Remove the load from the forks, boom or load platform before loading for transport. The transport vehicle must be secured to prevent rolling while the machine is being loaded. The machine must be securely fastened to the transport vehicle. OPERATING INSTRUCTIONS Lifting Instructions The number of people required to load and unload a machine is dependent on a number of factors, including but not limited to: · the physical condition, strength and disabilities or prior injuries of the people involved · the vertical and horizontal distances the machine has to be moved · the number of times the machine will be loaded or unloaded · the stance, posture and grip used by the people involved · the lifting techniques used · the site conditions and weather in which the activity is being performed (i.e., slippery, icy, raining) The appropriate number of people and proper lifting techniques must be used to prevent physical injury. Loading for Transport 1 Fully lower the carriage. 2 Rotate the carriage hold-down bar over the carriage. Be sure the lock pin snaps into place. 3 Remove the winch handle, reverse the handle and install it. The handle grip should face the carriage. 4 Models with electric winch: Remove the battery pack. Part No. 35566 Genie Lift First Edition • Sixth Printing Operator's Manual LOAD CAPACITY CHARTS Forks Load Capacity Chart 12 14 30 35 inches cm Model GL-4 lbs kg 500 500 227 227 GL-8 lbs kg 400 400 181 181 GL-10 lbs kg 350 350 159 159 GL-12 lbs kg 350 350 159 159 Maximum Load Centers (measure from front of carriage) Forks: 14 in 35 cm Load Platform: 14 in 35 cm Boom: 20 in 51 cm Boom Load Positioning Instructions 1 Determine the weight of the load and the location of its load center. 2 Refer to the chart below to determine if the machine is capable of lifting the weight at the location on the boom. 3 Attach the lifting shackle to the desired hole on the boom. Rear mounting hole Boom Load Capacity Chart Model Front Hole RearHole GL-4 lbs kg 300 136 500 227 GL-8 lbs kg 240 109 400 181 Front mounting hole GL-10 lbs kg 210 95 350 159 GL-12 lbs kg 210 95 350 159 Part No. 35566 Genie Lift Operator's Manual First Edition • Sixth Printing Specifications Model GL-4 GL-8 GL-10 GL-12 Height, maximum lift 5 ft 11 in 10 ft 1/2 in 11 ft 8 in 13 ft 91/2 in Forks up 1.8 m 3.1 m 3.6 m 4.2 m Height, maximum lift 4 ft 11/2 in 8 ft 3 in 9 ft 101/2 in 12 ft Forks down 1.2 m 2.5 m 3 m 3.7 m Height, minimum lift 31/2 in 31/2 in 2 in 2 in Forks down 8.9 cm 8.9 cm 5.1 cm 5.1 cm Lift capacity 500 lbs 400 lbs 350 lbs 350 lbs at 12 in / 30.5 cm load center 227 kg 181 kg 159 kg 159 kg Machine weight See specification chart on next page. Height, stowed* 5 ft 71/2 in 5 ft 71/2 in 6 ft 51/2 in 7 ft 63/4 in 1.7 m 1.7 m 2 m 2.3 m Ground clearance* 3/4 in 3/4 in 3/4 in 3/4 in 1.9 cm 1.9 cm 1.9 cm 1.9 cm Standard base Width 243/4 in 243/4 in NA NA 62.9 cm 62.9 cm Length - stowed 12 in 12 in NA NA 30.5 cm 30.5 cm Length - operating 343/4 in 343/4 in NA NA 88.3 cm 88.3 cm Straddle base Width - stowed 283/4 in 283/4 in 283/4 in 283/4 in 73 cm 73 cm 73 cm 73 cm Width - extended 431/2 in 431/2 in 431/2 in 431/2 in 1.1 m 1.1 m 1.1 m 1.1 m Length - stowed 191/4 in 191/4 in 191/4 in 191/4 in 48.9 cm 48.9 cm 48.9 cm 48.9 cm Length - operating 43 in 43 in 43 in 43 in 1 m 1 m 1 m 1 m Counterweighted base Width - stowed 283/4 in 283/4 in 283/4 in NA 73 cm 73 cm 73 cm Width - extended 431/2 in 431/2 in 431/2 in NA 1.1 m 1.1 m 1.1 m Length - operating 281/2 in 281/2 in 281/2 in NA 72.4 cm 72.4 cm 72.4 cm Airborne noise emissions by machinery Maximum sound level at normal operating workstations (A-weighted) Manual winch 90 dB 90 dB 90 dB 90 dB Electric winch 95 dB 95 dB 95 dB 95 dB * The 10 inch pneumatic rear wheel option will add 1 inch / 2.5 cm to these specifications. * The 4 point caster option B will add 1 inch / 2.5 cm to these specifications. * The counterweight base will add 1 inch / 2.5 cm to these specifications. 22 Genie Lift Part No. 35566 First Edition • Sixth Printing Operator's Manual SPECIFICATIONS Model GL-4 GL-8 GL-10 GL-12 Forks Length 221/2 in 221/2 in 221/2 in 221/2 in 57.2 cm 57.2 cm 57.2 cm 57.2 cm Width 201/2 in 201/2 in 201/2 in 201/2 in 52.1 cm 52.1 cm 52.1 cm 52.1 cm Load Platform Length 23 in 23 in 23 in 23 in 58...

Descargar ahora

Introduzca dos números de la imagen: