Votos - 3, Puntuación media: 4 ( )

Fabricar: Summit Tamaño del archivo: 1.78 mb Nombre del archivo: Idioma del manual:

as an average. Please seek help if you cannot lift them by yourself. Put the batteries into the battery boxes. Using the screws, washers, and nuts provided from the battery supplier, connect the red line to the Positive (+) terminal of a battery while connecting the black line to the Negative ( ) terminal of the same battery (Fig. 2). Close the box properly and carry it with the strap. Apply the same connecting method to both batteries. Fold down the battery bars on each side of the frame so that you can slide the battery boxes underneath the seat (Fig. 3). The battery box with the reset button and two outlet connectors should be put underneath the power chair first. The outlet connectors of the battery boxes should be put on the same side for connection. Connect the two battery connectors (Fig. 4). Put the battery supporting bar at the back of the battery box. Screw on the battery knobs to tightly fasten the bar (Fig. 5). + Fig. 2 Battery Bar Fig. 3 Battery Knobs Battery Connector Fig. 4 Fig. 5 Page 7 ASSEMBLY & DISASSEMBLY ASSEMBLY & DISASSEMBLY C. Installing the controller Your power wheelchair comes standard with a swing-away joystick controller. To install the controller, simply fasten it to the controller supporting bar with the two (2) black screws provided (Fig. 6). D. Connecting the main cables Plug the three main cables (connected to left, right motor and battery) underneath the seat near the crossbar to the connectors on the other end of the controller. Cables should be connected according to the indicated labels only, i.e. left to L (motor), right to R (motor), and middle cable to the battery cable only. ZWarning: Wrong connection can make the power wheelchair defective. Controller Supporting Bar Fig. 6 Fig. 7 E. Installing the anti-tippers Remove the pin on the anti-tipper. Insert the anti-tipper, one on each side, at the rear bottom of the frame. Snap the pins to fasten the anti-tippers (Fig. 8). F. Installing the footrests and strap Locate the pins for the footrests on the frame. Put the footrest, one at a time, to the wheelchair. Slide the footrest strap accordingly. Page 8 Pin Fig. 8 ASSEMBLY & DISASSEMBLY ASSEMBLY & DISASSEMBLY DISASSEMBLY A. Battery removal For transportation BUnplug the battery connector from the controller connector underneath the seat near the crossbar. Refer to Assembly, Section D, Connecting the main cables on Page 8. BUnscrew the knobs and remove the battery bar at the rear battery box. BUnplug the battery connector that joins the two battery boxes together. BSlide out the battery boxes, one at a time. BLift the battery boxes using the battery strap. For replacement BUnplug the battery connector from the controller connector underneath the seat near the crossbar. Refer to Assembly, Section D, Connecting the main cables on Page 8. BUnscrew the knobs and remove the battery bar at the rear battery box. BUnplug the battery connector that joins the two battery boxes together. BSlide out the battery boxes, one at a time. BLift the battery boxes using the battery strap. BUnlock the battery strap and remove the battery box cover. BRemove the battery post caps. BUnscrew positive terminals (+) one at a time. BUnscrew negative terminals ( ) one at a time. BRemove batteries one at a time. BFor installing the batteries, refer to Assembly, Section B, Installing the Batteries on page 7. Page 9 ASSEMBLY & DISASSEMBLY ASSEMBLY & DISASSEMBLY B. Folding the wheelchair To fold the wheelchair, it is necessary to remove certain components. Follow the simple guidelines below: BTurn the wheelchair off. BPark the chair on a level surface. BEnsure the wheels are in drive (engaged) mode, with controller lever on the vertical position (Fig. 9). BFold up the footrests and remove the entire footrests assembly. BRemove the battery boxes. You can refer to Disassembly, Section A, Battery Removal, For Transportation on page 9. BGrab the strap on the seat upholstery and pull upward. This will pull the entire frame together (Fig. 10). Fig. 9 Fig. 10 Page 10 ADJUSTMENTS FOR SEATING COMFORT ADJUSTMENTS FOR SEATING COMFORT To maximize seating comfort, your power wheelchair lets you adjust: BArmrest height. BController position. BFlip-back and detachable armrest. BFootrest height. A. Armrest height (Adjustable up to 4” in 1” increments) To adjust the armrest height, pull and hold the button on the arm sub-assembly, lift the armrest up to the desired height (Fig. 11). Release the button when the armrest is locked. B. Controller position Unscrew the lever underneath the armrest (Fig. 11). Slide the supporting bar for the controller to the desired length. Screw back the lever to lock the controller position. Controller can be placed either on the left side or on the right side. No extra spare parts are needed. C. Flip-back and detachable armrest The armrests can be flipped back to easily access the wheelchair (Fig. 12). You can flip back the arm Sub-assembly by pressing and holding the button located in the ...

Descargar ahora

Introduzca dos números de la imagen: