Votos - 2, Puntuación media: 4 ( )

Fabricar: Braun Tamaño del archivo: 1.49 mb Nombre del archivo: Idioma del manual:

Failure to do so may result in serious bodily injury and/or property damage. sales representative should also instruct and demonstrate manual operation procedures. Be certain your sales representative instructs and demonstrates the proper reengagement procedure of the manual cable release system (see pages 15-19). Any questions or concerns can be answered by the sales representative at that time. Do not operate your lift if you suspect lift damage, wear or any abnormal condition. Discontinue lift use immediately and contact an authorized Braun Corporation dealer in your area or call The Braun Corporation at 1-800-THE LIFT. One of our national service representatives will direct you to an authorized service repairman who will inspect your lift. Preventive Maintenance: Maintenance is necessary to ensure safe and trouble-free lift operation. General preventive maintenance consisting of careful inspections of your lift system and cleaning the lift should be a part of your routine. Simple inspections can detect potential lift operational problems. Regular preventive maintenance will reduce potential lift operation downtime and increase the service life of the lift, as well as possibly detecting potential hazards. Exposure to harsh weather elements or environmental conditions may require more frequent maintenance and lubrication procedures. See the Maintenance and Lubrication section for further details. Cold Climate Recommendations: The vehicle in which the lift is installed should be stored in a garage or other sheltered place if possible, especially during inclement weather conditions. When the lift is not in use, the lift should be in the stowed position to keep foreign objects, rain, ice, snow, etc., from entering through the lift opening or building up on the platform surface. Lift Operating Instructions Lift Operating Instructions address the lift control switches and the corresponding lift functions. Separate instructions are provided for operation of manual bridge plates (inboard roll stops) and handrails that may be present on your particular lift model. Fold handrails down before stowing lift. In event of power or equipment failure, refer to the Manual Operating Instructions section. Before lift operation, park the vehicle on a level area, away from vehicle traffic. Place the vehicle transmission in “Park” and engage the parking brake. Vehicle Lift Door(s): Open manual doors fully, being certain the doors are secured in the fully open position before operating the lift. If your vehicle is equipped with optional automatic door operators, the doors will open when the UP or DOWN switch is pressed. The automatic door operators will close when DOOR CLOSE switch is pressed (only if the lift platform is in the fully stowed position). Page 10 Lift Operating Instructions Lift Control Switches: The UVL® logic control system provides fully automatic operation of all lift functions as well as optional automatic door operators (if so equipped). Lift functions can be performed from any position the platform happens to be in at the time the switch button is pushed. There are two types of hand controls available for the UVL - the standard hand-held control switchbox, or the optional remote control. Both types of controls are equipped with four push-button switches. The functions activated by both types of controls are the same. The switch functions are labeled. The function of each switch is described below. Remote Control Note: The effective range of the remote control is 20 feet. A range further than 20 feet does not allow an attendant to observe and assist the lift passenger. Control Switch Functions: UP LIFT DOWN LIFT LIFT 81812 DOOR CLOSE STOW Hand-held Switchbox (Standard Equipment) UP STOW DOOR CLOSE DOWN THE BRAUN CORPORATION 86478 Optional Remote Control Transmitter UP: From the stowed position, the LIFT UP function deploys (extends) the platform fully. The platform then raises to floor level height and moves inward to the vehicle floor level position (if applicable). Note: When the lift is in the stowed position, power doors automatically open when the UP switch is pressed (if so equipped). From ground level, the LIFT UP function will first automatically raise (rotate) the outboard roll stop to the upright (vertical) position. Note: The lift will not raise if the roll stop is not in the UP position (built-in safety feature). The platform then raises to floor level height and moves inward to the vehicle floor level position. Note: UVL600 and UVL600X lift models move inward to floor level position with an “arcing” motion. UVL850 Series lift models do not. DOWN: The LIFT DOWN function lowers the platform to ground level (regardless of the position of the platform) and then unfolds the outboard roll stop to the ramp (horizontal) position. From the stowed position, the lift will extend and then lower. Note: When the lift is in the stowed position, power doors automatically open when the DOWN switch is pressed (if...

Descargar ahora

Introduzca dos números de la imagen: