Votos - 3, Puntuación media: 4 ( )

Fabricar: Pride Mobility Tamaño del archivo: 3.93 mb Nombre del archivo: Idioma del manual:

Quantum 6000Z Series 21 INITIAL ASSEMBLY Your power chair may require some assembly either before initial use or after transportation. It may also require disassembly to make some comfort adjustments. Figure 10 details those parts of the power chair that are designed to be disassembled and assembled by an end user or by a qualified caregiver before using the product or making comfort adjustments. NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores or through your Quantum Rehab Provider. IV. ASSEMBLY ARMREST ANGLE ADJUSTMENT Figure 10. Quantum 6000Z Series Assembly View (Synergy Seat Shown) FOOT PLATFORM HEIGHT/DEPTH ADJUSTMENT SEAT HEIGHT/ANGLE ADJUSTMENT CONTROLLER POSITION FOOT PLATFORM ANGLE ADJUSTMENT 22 Quantum 6000Z Series LATCHED IV. ASSEMBLY Seat Installation It may be necessary to install the seat either prior to initial operation or after transporting your power chair. Contour seats are attached to the power base with the Universal Mounting System (UMS). The UMS consists of universal parts that may be attached to the seat, regardless of seat width or seat depth. The two main components are aluminum extrusions mounted to the seat base. These extrusions attach to a pair of trapeze bars that are mounted to the power base. See figure 11. NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or a TRU-Balance Power Positioning System, refer to the information provided in separate manuals. WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of the seat if they do so. To install the seat: 1. Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 11. 2. Lower the front extrusion onto the front trapeze bar until the seat locks into place. 3. Flip the seat latch safety down. WARNING! Make sure the seat latch safety is flipped down before using your power chair. 4. Install the controller and route the harness to the back of the power base. See figures 12 and 13. 5. Loosen the rear shroud fasteners and remove the rear shroud. See figure 6. 6. Plug the controller connector into the power base. See figure 7. 7. Replace the rear shroud and tighten the rear shroud fasteners. See figure 6. 8. Secure the controller harness to the armrest receiver with wire ties (contour seats only). See figure 13. MANDATORY! Prevent controller harness damage! Avoid routing the controller harness on the outside of the armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use correct tiedown points for controller harness to prevent the harness from getting caught in the drive tires, pinched in the seat frame, or damaged when passing through doorways. Figure 11. Universal Mounting System and Contour Seat SEAT LATCH SAFETY REAR EXTRUSION FRONT EXTRUSION TRAPEZE BARS Figure 12. Controller Routed on a TRU-Balance Power Tilt UNLATCHED Quantum 6000Z Series 23 IV. ASSEMBLY Power Elevating Seat Installation Your power chair may be equipped with the power elevating seat option. While the seat itself may be any one of the styles offered for this model, the way the seat base attaches to the power base is different. To install the power seat: l. Place the seat plate interface bracket onto the actuator. See figure 14. 2. Insert screws into the actuator and insert and tighten the hardware. See figure 14. 3. Place seating system onto the seat plate interface bracket and secure. Transit Securement System (Optional) If your power chair is equipped with a transit securement system, it is equipped with manufacturerinstalled front and rear securement brackets and positioning belt anchoring brackets. See figure 15. Refer to the supplement provided with your power chair for information on how to use the transit securement system. NOTE: In certain configurations, the transit securement system is not available on power chairs equipped with an HD option. Figure 14. Power Seat Actuator ACTUATOR SEAT PLATE INTERFACE BRACKET WIRE TIES Figure 13. Controller Routed on a Contour Seat Figure 15. Transit System Securement Brackets SECUREMENT BRACKETS (3 OF 4 SHOWN) POSITIONING BELT ANCHORING BRACKET LOCATIONS (1 OF 2 SHOWN) 24 Quantum 6000Z Series COMFORT ADJUSTMENTS After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase your comfort, such as seat height and angle, armrest width, armrest angle and height, foot platform height, depth, and angle, and controller position. NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or Synergy TRU-Balance Power Positioning System, refer to the information...

Descargar ahora

Introduzca dos números de la imagen: