Votos - 2, Puntuación media: 3.5 ( )

Fabricar: Shoprider Tamaño del archivo: 513.45 kb Nombre del archivo: midsize_manual.pdf Idioma del manual:

NOTE! There is no easy way to evaluate the overall immunity of the scooter. 5. Report all incidents of unintended movement or braking to your Shoprider® provider, and note whether there are sources of EMI nearby. WARNING: Shoprider® Mobility Products is not responsible for damage or injury incurred due to improper and unsafe use of our scooter. 5/11/2004 6 ADJUSTMENTS Tiller Angle Adjustment (Fig. 5A&B) On the left hand side at the base of the tiller is a red lever/black knob. Push/pull the lever to release the pin and select the required tiller angle. Refit the pin into one of the five location holes. Seat Slide & Swivel Adjustment (Fig. 6) Figure 5A Tiller Angle Adjustment Lever Tiller Angle Adjustment Knob Figure 5B Pulling up on the seat slide lever allows the seat position to be adjusted forward or backward. Release the lever and the seat will lock in that position. Under the right side of the seat there is a spring loaded red lever. Pulling up on the lever allows the seat to swivel, when released the seat will lock into one of 4 positions. Seat Removal (Fig. 7) Fold down the back of the seat. Pull up the swivel seat adjustment lever (fig. 6) and lift seat off. Remove the hand-knob and locking pin that secures the seat adaptor. Lift the seat adaptor out of the seat post. Seat Height Adjustment (Fig. 7) Remove seat as described above. Loosen the seat tightening hand knob. The seat height can be adjusted to 5 different settings by inserting the steel locking pin in the required hole. Retighten the hand knob and replace the seat. Seat Slide Lever Swivel Seat Adjustment Lever Figure 6 Seat Adaptor Seat Tightening Hand Knob Seat Locking Pin Armrest Width Adjustments (Fig. 8) Figure 7 On the underside of the seat there are two hand knobs, one either side. Loosening the hand knob allows the arm rest to be adjusted to the required width, or removed for transportation. Do not use the scooter without the arms being fitted. Armrest Adjustment Hand Knob Figure 8 5/11/2004 7 Armrest Angle Adjustment (Fig. 9) Flip up the armrests to allow access to the adjustment screw and lock nut, unscrew the lock nut and screw the bolt in or out to increase or decrease the angle. Re-tighten the lock-nut. Your scooter is dispatched from the factory with the armrests set parallel to the floor. Retractable charger cord (FOR Sunrunner™ 3 Deluxe & Sunrunner™ 4 Deluxe ONLY) (Fig. 10) Pull cord by the cord handle to length desired. To retract cord, slightly pull cord and release. Cord will retract automatically. WARNING!! Releasing the cord too fast can cause the cord to hit the shroud and crack it!! Locking Nut and Bolt Adjustment Screw Figure 9 Retractable charger cord Figure 10 5/11/2004 8 SCOOTER TILLER CONTROLS (FIG. 11A&B) Speed Controls The speed control allows you to set a speed between 1 (minimum) and 10 (maximum). Battery Level Indicator The number of LED bars lit, shows the amount of charge left in your batteries. The amount of charge will only show at its true level when the scooter is in drive. Caution – Do not allow the LED bars go out completely as complete discharge of the batteries could cause irreversible damage. Lights A blue colored button at the rear of the tiller operates the lights. Horn A yellow button at the rear of the tiller operates the horn. Thumb/Finger Lever Controls The left thumb/finger lever controls the reverse and the right thumb/finger lever controls the forward motion. The amount of pressure applied to each lever will determine the speed the scooter travels at. Release the lever and the scooter will slowly come to a stop and the electromagnetic brake will be applied. On/Off Key Switch Insert the key in the right side of the tiller. Turn the key and the LED bars will light up. There is a delay before the thumb/finger lever control can be operated, while the controller is checking the circuits. Indicator Switch Operates turn indicator lights. Hazard Warning Switch A red button operates all indicator flashers. Figure 11A Battery Level Indicator Horn Key Switch Thumb Lever Control Light Speed Controls 5/11/2004 9Figure 11B Lights Finger Lever Control Hazard Lights Battery Level Indicator Indicator Switch Speed Controls Key Switch Electromagnetic Brake The brake is automatically operated when the control levers are released. There is a slight delay when the scooter decelerates; this allows the scooter to come to a smooth stop. FREE WHEEL OPERATION (FIG. 12) The free wheel release lever (red handle) is located inside the right rear wheel (Fig. 12). To disengage the motor, lift up the lever (the scooter can now be pushed). To re-engage the motor push down on the lever. WARNING! Always re-engage the free wheeling device after use. Failure to do so may result in injury. Anti-tip wheels The anti-tip wheels are located at the rear of the scooter frame (Fig. 12). The scooter should not be used unless the anti-tipping wheels are in place. Shoprider® Mobility Products is not responsible for damage or injury incur...

Descargar ahora

Introduzca dos números de la imagen: