Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
4. Flip the seat latch safety down. WARNING! Make sure the seat latch safety is flipped down before using your power chair. 5. Install the controller into one of the armrests. See V. “Comfort Adjustments.” 6. Route the controller cable so that it cannot be pinched in the seat hinge. 7. Slide the rear cover open to expose the electronics tray. 8. Plug the controller connector into the electronics tray. See figure 6. 9. Secure the controller cable to the armrest receiver with one or more wire ties. Power Elevating Seat Installation (Optional) Your power chair may be equipped with a power elevating seat option. While the seat itself may be any one of the styles offered for this model, the way the seat base attaches to the power base is different. To install the power elevating seat: l. Align the seat post on the seat base to the hole in the actuator. See figure 11. 2. Insert the seat post into the actuator and push the seat lever forward to lock the seat into place. 3. Plug the power elevating seat switch cable into the connector on the electronics tray. Figure 11. Power Elevating Seat Actuator Quantum 1122 Series V . COMFOR T ADJUSTMENTS V . COMFOR T ADJUSTMENTS COMFORT ADJUSTMENTS After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and the controller’s position. NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or Synergy TRU-Balance, refer to the information provided in separate manuals. If your power chair is equipped with a contoured seating system, refer to the following information. WARNING! If your power chair was configured at your Quantum Rehab Specialist, please consult your healthcare professional before changing the seat position or making any other adjustment. Some adjustments may degrade your power chair’s performance and safety by changing its center of gravity. WARNING! Some power chair components are heavy. You may need assistance to lift or carry them. Please refer to the specifications table for specific component weights before you disassemble the power chair. WARNING! Remove the occupant from the power chair before making any adjustments. You may need the following to make comfort adjustments: • metric/standard hex key set • metric/standard socket set and ratchet • adjustable wrench Seat Height/Angle Adjustment The seat is attached to the power base through the UMS. You can change the seat height by raising the front and rear trapeze bars. If you raise or lower only one set of trapeze bars (front or rear), you can also change the seat base angle (dump). To change the seat height: 1. Turn off the power to the controller. 2. Unplug the controller connector(s) from the electronics tray. 3. Flip up the seat latch safety. See figure 12. 4. Squeeze the seat latch and release the seat from the front trapeze bar. 5. Slide the seat forward and remove it from the power base. 6. Remove the quick-release pins from the seat towers (front and rear). See figure 13. 7. Remove both trapeze bars from the seat towers. 8. Lift off the shroud 9. Remove the ball detent pin from each of the four seat towers. See figure 13. Figure 12. Seat Latch Safety (Disengaged) Figure 13. Seat Height Adjustment QUICK-RELEASE PINS TRAPEZE BARS BALL DETENT PINS SEAT TOWER Quantum 1122 Series V . COMFOR T ADJUSTMENTS V . COMFOR T ADJUSTMENTS 10. Move the seat towers up or down to the desired height. 11. Reinstall the ball detent pin into each seat tower. 12. Reinstall the shroud. 13. Reinstall the trapeze bars and secure with the quick- release pins. 14. Reinstall the seat. WARNING! Make sure the seat latch safety is flipped down before using the power chair. 15. Plug the controller connector(s) into the electronics tray. Seat Position You can move the seat forward or rearward by changing the extrusion mounting position. To change the seat position: 1. Turn off the power to the controller. 2. Unplug the controller connector(s) from the electronics tray. 3. Remove the seat from the power base. 4. Remove both extrusions from the bottom of the seat. 5. Reposition the extrusions on a different set of mounting holes. You must move both extrusions the same number of holes either forward or backwards. See figure 14. 6. Fasten the extrusions back onto the bottom of the seat. 7. Reinstall the seat. 8. Plug the controller connector(s) into the electronics tray. Manual Recline Seatback Adjustment If your power chair is equipped with a reclining seat, you can adjust the seatback angle with the seatback release lever. The lever is located on the right side of the seat base. To adjust the seatback angle: 1. Pull up on the seatback release lever. 2. Move the seatback down or up to the desired position. 3. Release the lever. Headrest Height Adjustment If your power chair is equipped with an optional deluxe high-back seat, ...