Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
2. Turn the nut clockwise until it is snug. 3. Rotate the lever until it is in the fully closed position. NOTE: If the lever will not rotate to the fully closed position, then turn the nut counterclockwise one-quarter or one-half turn. Foot Platform Angle Adjustment You can adjust the angle of the foot platform with a hex key. See figure 21. To adjust the foot platform angle: 1. Flip up the foot platform and locate the setscrew. 2. Turn the setscrew counterclockwise to raise the front of the foot platform. 3. Turn the setscrew clockwise to lower the front of the foot platform. Controller Position You can position the controller for either left-hand or right- hand use. WARNING! Do not place the controller cable so that it can be pinched in the seat frame or the power base frame. To change the controller position: 1. Turn off the power to the controller. 2. Disconnect the controller from the power base. 3. Cut the wire tie(s) that attaches the controller cable to the armrest. 4. Flip up the armrest and loosen the setscrew. Seefigure 22. 5. Slide the controller out of the armrest. 6. Loosen the setscrew in the other armrest. 7. Place the controller in the other armrest. 8. Tighten the setscrew to secure the controller. 9. Use a wire tie to secure the controller cable to the armrest. 10. Plug the controller into the power base. See figure 6. Figure 22. Underside of Armrest SETSCREW Figure 23. Swing-Away Footrests Figure 21. Underside of Foot Platform SETSCREW ADJUSTMENT SCREWS FOOTREST EXTENSION SFR RELEASE LEVER Jazzy 1107 28 Jazzy 1107 Multi-Axis Foot Plates The multi-axis foot plate assembly can be installed on either a swing-away footrest or an elevating leg rest. The multi-axis foot plate has four adjustments: leg rest length (A), position (B), tilt (C), and angle (D). See figure 25. To change leg rest length (A): 1. Remove the hardware. 2. Move the leg rest to the desired position. 3. Reinstall the hardware. B C D A Figure 25. Multi-Axis Foot Plate (ELR Shown) SETSCREW LOCATION V. C O M F O R T A D J U S T M E N T S Swing-away Footrests Swing-away Footrests (SFRs) enable you to rotate the footrests to the side before you transfer onto or off of your power chair. To rotate the SFRs: 1. Push in the release lever. See figure 23. 2. Rotate the SFRs. To adjust the SFR length: 1. Remove the two adjustment screws from the side of each footrest extension. See figure 23. 2. Slide the footrest up or down to the desired length. 3. Reinstall the two adjustment screws. Elevating Leg Rests Elevating Leg Rests (ELRs) offer an infinite range of adjustment for the leg angle and a footrest adjustment range of 12–19 in. To rotate the ELRs: 1. Push in release lever A. See figure 24. 2. Rotate the ELRs. To adjust the ELR length: 1. Remove the two adjustment screws from the side of each leg rest extension. See figure 24. 2. Slide the leg rest up or down to the desired length. 3. Reinstall the two adjustment screws. To adjust the ELR angle: 1. Push down release lever B. See figure 24. 2. Move the leg rest to the desired angle. ADJUSTMENT SCREWS Figure 24. Elevating Leg Rests LEG REST EXTENSION RELEASE LEVER B RELEASE LEVER A V . C O M F O R T A D J U S T M E N T S V . COMFORT ADJUSTMENTS NUT A BOLT B To change foot plate position (B): 1. Remove the hardware. 2. Move the foot plate to the desired position. 3. Reinstall the hardware. To change foot plate tilt (C): 1. Loosen the hardware. 2. Tilt the foot plate to desired position. 3. Tighten the hardware. To change foot plate angle (D): 1. Turn the setscrew clockwise to decrease the angle. 2. Turn the setscrew counterclockwise to increase the angle. Anti-Tip Wheels The anti-tip wheels are designed to give your power chair increased stability on rough surfaces. The anti-tip wheels are preset at the factory for smooth surfaces or indoor use only. If you plan on using your power chair on rough surfaces, it may be necessary to adjust the anti-tip wheels to better suit your needs. The anti-tip wheels may need ad- Figure 26. Anti-Tip Wheel Assembly justment if the following occurs: • When coming to a stop, your power chair tips forward excessively. • The anti-tip wheels constantly rub the ground. WARNING! Consult your authorized Pride Provider before attempting to change the anti-tip wheel height! Changing the anti-tip wheel height affects handling under acceleration! WARNING! The higher you raise the anti-tip wheels, the more you increase your power chair’s tendency to tilt forward while decelerating. You can compensate for this by having your authorized Pride Provider make a small adjustment to the pre-programmed deceleration setting in the controller or by moving the seat assembly farther to the back of your power chair. PROHIBITED! Do not remove the anti-tip wheel NOTE: Each drive tire must be inflated to 35 psi (2.4 bar) if equipped with pneumatic tires. The user must also be seated in the power chair in order to properly adjust the anti...