Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
See figure 1. There are a variety of seating options that are designed to accommodate most users. Typically, the seating system includes armrests, seatback, seat base, and joystick. Your Jazzy seat may also have some optional accessories attached to it, such as a basket, cane/crutch holder, a cup holder, or a power seat switch. The power base is the heart of the Jazzy. The power base assembly includes two motor/brake assemblies, two anti-tip assemblies, two drive wheels, two anti-tip wheels, a caster assembly with two rear casters, two batteries, power seat actuator (optional), a connector housing, and all wiring harnesses. See figure 1 below and figures 2 and 3. ARMRESTS SEAT JOYSTICK CONTROLLER SEATASSEMBLY BODY SHROUD POWERBASEASSEMBLY CASTER WHEEL ANTI-TIP WHEELS DRIVE WHEEL FIGURE 1. The Jazzy 1103 8 Jazzy 1103 III. OPERATION Specifications Suspension: Full suspension Drive Wheels: 25 cm pneumatic, center-mounted (solid tyres are optional) Rear Casters: 20 cm solid, rear articulating Anti-tip: 15 cm solid, front mounted Max. Speed: 6 km/hr Brakes: “Intelligent Braking,” electronic regenerative, disc park brake Ground Clearance: 9 cm Turning Radius: 47 cm Overall Size: Length: 91 cm Width: 58 cm Seating Options: Low Back Medium Back (standard) Highback with headrest Power Elevating Option Available Drive Train: Two-motor, mid-wheel, high speed Batteries: Two 12 volt, U-1 batteries Range: Up to 32 km Battery Charger: 5-amp Off-board 3-amp Onboard (optional) Electronics: 50-amp Pilot Controller Weight Capacity: 113 kg/18 stone Component Weights: Base: 37 kg Seat: 13 kg Batteries: 11 kg each Warranty: Lifetime limited warranty on frame 2-year electronics warranty 18 months on drive motors Jazzy 1103 9 III. OPERATION SEAT2POST MOTORGBRAKEASSEMBLY FIGURE 2. Jazzy 11O3 Power Base (shroud removed) FIGURE З. Electronics Connector Housing (non power seat) lO Jazzy !ЮЗ III. OPERATION ELECTRONICS CONNECTOR HOUSING The connector housing is located on the rear of the Jazzy. See figure 3. The connector housing holds the main circuit breaker and controller harness connectors. Main circuit breaker: The main circuit breaker is a safety feature built into your Jazzy 1103. When the batteries and the motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips to prevent damage to the motors and the electronics. If the circuit trips, allow the Jazzy to “rest” for approximately one minute. Then, push in the circuit breaker button, turn the controller power back on, and continue normal operation. If the main circuit breaker continues to trip repeatedly, contact your authorized Pride provider. Controller Harness Connectors: These are where the joystick cables connect to the power base. For convenience, your Jazzy 1103 is equipped with two freewheel levers. See figure 2. These levers allow you to disengage the drive motors and maneuver the chair manually. To engage or disengage the drive motors: 1. Locate the two (2) metal levers protruding from the body shroud. 2. Turn them outward to engage the drive motors. 3. Turn them inward to disengage the drive motors. If the lever is difficult to move in either direction, slightly rock the Jazzy 1103 back and forth. The lever should then move to the desired position. Remember: When the Jazzy 1103 is in the freewheel mode, the braking system is disengaged. FREEWHEEL LEVERS A WARNING: DO NOT use the Jazzy 1103 while the drive motors are disengaged! DO NOT disengage the drive motors when the Jazzy 1103 is on an incline, as the unit could roll on its own, causing injury! Jazzy 1103 ll III. OPERATION BATTERIES AND BATTERY CHARGING Your Jazzy 1103 uses two long-lasting, 12-volt batteries. These batteries are sealed, maintenance-free, deep-cycle batteries. Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a deep discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable. Automotive batteries are not designed to handle a long, deep discharge and also are unsafe. A WARNING: You must recharge your Jazzy 1103’s batteries with the supplied off-board charging system. Do not use an automotive-type battery charger! To charge the batteries using the off-board charger: 1. Position your Jazzy 1103 close to a standard wall outlet. 2. Be certain the controller power is turned off and the Jazzy is not in freewheel. 3. Insert the 3-pin charger lead plug into the joystick programming port located at the front of the Jazzy’s joystick controller. See figure 11. 4. Extend the charger power lead and plug it into the wall outlet. The Jazzy 1103 incorporates an inhibit function that disables the powered wheelchair when the charger is plugged into a wall outlet. 5. We recommend you charge the batteries for 8 to 14 hours. As the batteries charge, the indicator lights located on the back of the char...