Iniciar sesión:
Votos - 2, Puntuación media: 4.5 ( )

Manual de usuario Razor, modelo E500S

Fabricar: Razor
Tamaño del archivo: 1.6 mb
Nombre del archivo: 5982d7ae-be25-49a0-b596-d7047b4ad809.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


To reinstall wheel, reverse these steps. SB 1918 (CALIFORNIA) DECLARATION YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC VEHICLE. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT. 6 TROUBLESHOOTING GUIDE Problem Possible Cause Solution Scooter does not run Scooter was running but suddenly stopped Undercharged battery Charger is not working Loose wires or connectors Burned out fuse Motor or electrical switch damage Charge the battery. A new battery should have been charged for at least 12 hours before using the scooter for the first time and up to 8 hours after each subsequent use. Check all connectors. Make sure the charger connector is tightly plugged into the charging port, and that the charger is plugged into the wall. Make sure power flow to the wall outlet is on. You may check to see if your charger is working by using a volt meter or asking your local Razor authorized service center to test your charger for you. Check all wires and connectors to make sure they are tight. The fuse will burn out and automatically shut off the power if the motor is overloaded. An excessive overload, such as too heavy a rider or too steep a hill, could cause the motor to overheat. Replace the fuse with a new one of equal amperage. Correct the conditions that caused the fuse to burn out and avoid repeatedly burning out fuse. Contact your local Razor authorized service center for diagnosis and repair. Short run time (less than 30 minutes per charge) Scooter runs sluggishly Undercharged battery Battery is old and will not accept full charge Brake not adjusted properly Driving conditions are too stressful Tires are not properly inflated Scooter is overloaded Brake rotor is dragging on pads Brake not adjusted properly Charge the battery. A new battery should have been charged for at least 12 hours before using the scooter for the first time and up to 8 hours after each subsequent use. Check all wires and connectors. Make sure the battery connector is tightly plugged into the charger connector, and that the charger is plugged into the wall. Make sure power flow to the wall outlet is on. Even with proper care, a rechargeable battery does not last forever. Average battery life is 1 to 2 years depending on scooter use and conditions. Replace only with a Razor replacement battery. Refer to adjusting the brake instructions on page 4. Use only on solid, flat clean and dry surfaces such as pavement or level ground. The tires are inflated when shipped, but they invariably will lose some pressure between the point of manufacturing and your purchase. Refer to instructions on page 5 of this manual to properly inflate tires. Make sure you do not overload the scooter by allowing more than one rider at a time, exceeding the 220 lb. maximum weight limit, going up a hill or towing objects behind the scooter. If the scooter is overloaded, the circuit breaker may trip and shut off power to the motor. Correct the driving conditions that caused the overload, wait a few seconds, and then push the breaker to reset the circuit. Avoid repeatedly tripping the circuit breaker. Use your fingers to twist the caliper adjuster in either direction until rotor is centered between pads. Refer to adjusting the brake instructions on page 4. 7 TROUBLESHOOTING GUIDE Problem Possible Cause Solution Sometimes the scooter doesn’t run, but other times it does Loose wires or connectors Motor or electrical switch damage Check all wires around the motors and all connectors to make sure they are tight. Contact your local Razor authorized service center for diagnosis and repair. Charger gets warm during use Normal response to charger use No action required. This is normal for some chargers and is no cause for concern. If your charger does not get warm during use, it does not mean that it is not working properly. Scooter does not stop when applying the brake Brake not adjusted properly Refer to adjusting the brake instructions on page 4 . Scooter makes loud noises or grinding sounds Chain is too dry Brake rotor is dragging on brake pads Apply a lubricant such as 3 in 1TM or Tri-FlowTM to the chain. Use your fingers to twist the caliper adjuster in either direction until rotor is centered between pads. Need Help? Visit our web site for updates and a list of authorized service centers at or call toll-free at 866-467-2967 Monday -Friday 8:00 AM -5:00 PM Pacific Time. 8 E500S PARTS Keep your E500S scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part avail ability. (Specifications subject to change without notice.) 1. Front wheel with tire, tube, axle nuts 2. Rear wheel with tire, tube, sprocket, freewheel, axle nuts 3. Fork 4. Handlebar 5. Quill and handlebar clamp 6. Brake levers 7. Speed control 8. Seat mast w/screws 9. Chainguard w/screws 10. Sprocket and freewheel 11. Chain 12. Chain tensioner w/sc...


Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría