Votos - 5, Puntuación media: 3.6
(
)
)
|
Resumen del manual
INSTALLATION WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely. . . . ! " # $ . SAVE THESE INSTRUCTIONS NOTE: Check all parts for shipping damage before using. In case of damage, DO NOT use the equipment. Contact the Dealer/Carrier for further instructions. SAFETY SUMMARY The following recommendations are made for safe installation of the Solid Seat. GENERAL WARNINGS ADULT/HEMI REMOVABLE ARM WHEELCHAIR Seat Upholstery Seat Guides (REAR) and Tension Springs Reinsert Two (2) Screws Here Seat Guides Crossbrace (Front of Chair) Pivot Nut Crossbrace Pivot Bolt INSTALLING THE SOLID SEAT MODEL 1000 AND TRACER LX WHEELCHAIRS ONLY (FIGURES 1-5) NOTE: If not stated specifically, the procedure refers to both Adult/Hemi, Removable, and Permanet Arm Wheelchairs. 1. Remove wheelchair arms. NOTE: Some wheelchairs may have permanent arms. 2. Fold chair. 3. Remove seat upholstery (All Chairs) and reinsert two (2) screws behind the front two (2) spacers on the seat rails (Adult/Hemi Removable Arm) (FIGURE 1). 4. Remove the crossbrace pivot bolt and locknut from crossbrace (FIGURE 1). 5. Lift one (1) seat guide (front of chair) up and out of the side frame (Removable arm only) (FIGURE 1). 6. Remove the rear seat guide and tension spring from the seat rail (FIGURE 1). NOTE: For Permanent Arm Wheelchairs remove seat guides from front and rear of chair (FIGURE 1). 7. Repeat steps 5 and 6 for opposite side frame. PERMANENT ARM Seat Guides and Tension Springs (REAR) Crossbrace Pivot Nut Seat Guides (Front) Crossbrace Pivot Bolt FIGURE 1 - DISASSEMBLY OF THE WHEELCHAIR TO INSTALL SOLID SEAT 1 (1) Spacer A Screw A* (1) Spacer (1) A (1) Spacer (1) Screw B (2) Spacers (2) Solid Seat X-Brace ADULT REMOVABLE ARM WHEELCHAIR (REAR) Screw B (2) Spacers (2) (1) Spacer A Seat Rails ADULT/HEMI PERMANENTARMWHEELCHAIR (REAR) A (1) Spacer SPACER LENGTH A = 31/32-inch B = 7/16-inch *NOTE: These are the original spacers and remain on the chair in their current location. Screw NOTE: Before reassembling the chair, be sure to check the position of all the spacers on the seat rail. Refer to FIGURE 2. NOTE: Spacer positioning for the removable model is HEMI REMOVABLE ARM different between Adult and Hemi. Refer to FIGURE 2. WHEELCHAIR (REAR) FIGURE 2 - SEAT RAIL SPACER POSITION Solid Seat X-Brace Solid Seat X-Brace Screw Spacer (1)* Spacer (1)* 2 Screw B (2) Spacers (2) Screw *Spacer (1) *Spacer (1) Screw 8. Remove both X-Braces from the solid seat (FIGURE 3). 9. Remove the 5/16-18 x 1-inch bolt and the 5/16-18 locknut that secure the two (2) halves of one (1) X- Brace together. Leave the other X-Brace intact (FIGURE 3). Solid SeatREAR 5/16-18 x 1-inch Bolt 5/16-18Nut Solid Seat Mounting Screws X-Braces Solid Seat Mounting Screws Top View Front of Seat FIGURE 3 - REMOVING THE X-BRACESFROM THE SOLID SEAT 10. Take one (1) half of the X-Brace and slide it over the rear of each seat rail (FIGURE 4). NOTE: Before reassembling the chair, be sure to check the position of all the spacers on the seat rail. Refer to FIGURE 2. 11. Replace one (1) of the screws in the last upholstery mounting hole on each seat rail (FIGURE 4). Mounting ScrewsSeat Upholstery X-Brace Seat Rails FIGURE 4 - X-BRACE INSTALLATION 12. Replace the tension spring and the seat guide into the seat rails (FIGURE 1). NOTE: For Permanent Arm Wheelchairs replace seat guides in front and rear of chair (FIGURE 1). 13. Replace the front seat guide into its side frame side frame (Removable Arm ONLY) (FIGURE 1). 14. Reposition rear seat guide in front of the back canes (FIGURE 1). 15. On permanent arm models, front solid seat X-Braces must be installed before front seat guides are in place. NOTE: On the Permanent Arm Wheelchair, position the front seat guides behind the permanent arms. 16. Repeat this procedure for the opposite seat rail. NOTE: Before reassembling the chair, be sure to check the position of all the spacers on the seatrail. Refer to FIGURE 2. 17. Replace crossbrace pivot bolt and locknut (FIGURE 1). NOTE: When tightening the pivot bolt and locking nut make sure that there is only 1/8-inch of thread showing at the end of the pivot bolt. 18. Secure the two (2) sections of the rear solid seat X-Brace together with a 5/16 x 1-inch bolt and nut (FIGURE 3). NOTE:Tighten bolt and nut on X-Braces enough to minimize side play and still allow X-Braces to pivot when folding the chair. 19. Slide the other X-Brace assembly over the front of the seat rails (FIGURE 5). 20. Secure the seat to the X-Braces with four (4) #10-32 x 1-3/8-inch screws (FIGURE 3). 3 Top View Front of Seat Spacers Slide X-Brace Over Seat Rails Spacers Seat Rails Top View Front of Seat Spacers Slide X-Brace Over Seat Rails Spacers Seat Rails FIGURE 5 - ASSEMBLY OF THE FRONT X-BRACE INSTALLING THE SOLID SEAT TRACER IV ONLY (FIGURE 6) NOTE: Refer to the GENERAL WARNINGS in the SAFETY SUMMARY of this Instruction Sheet. NOTE: Ri...