Handle Height Adjustment 6 Positions Unpacking When unpacking, make sure item is intact and undamaged. If parts are missing or broken, call Harbor Freight Tools at 1-800-444-3353. Important SAFETY Information Assemble according to these instructions. 1. Improper assembly can create hazards. WARNING! 2. This product should only be used by a person who has the physical capability to safely walk and sit on this device. Do not exceed 225 lb. weight capacity. 3. Be aware of dynamic loading! Sudden lo

Do not modify the Walker and do not use the Walker for a purpose for which it was not intended. 5. Check for damaged parts. Before using any product, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for any broken or damaged parts and any other conditions that may affect its operation. Replace or repair damaged or worn parts immediately. 6. Replacement parts and accessories. When servicing, use only iden

1. Position the Stop Bar (3) and Lifting Frame (2) as shown in the Assembly Drawing, so that the holes on the arms of both the Stop Bar (3) and Lifting Frame (2) line up with the holes on the welded tabs on the Rear Lift Arms (4). Place Pins (28) through the Lifting Frame (2), the Tabs, Bushings (32), and Stop Bar (3). Please note:The Bushings fit around the Bolts and inside the Stop Bar. 2. Secure the Bolts with Washers (29 and 30) and Spring Pin (38). Installing the Pedal, Spring, and Handle.

b. Inspect before every use; do not use if parts loose or damaged. c. Turn vehicle’s ignition OFF and set parking brake. d. Clean dirt, oil and debris off Ramp and allow Ramp to dry. e. Unfold Ramp completely. f. Set up only on solid, level, dry surface. g. Turn Ramp so flange end faces downward. Position Ramp so that tongues fully contact tailgate. h. Properly connect safety chains. 2. Load vehicle slowly. Do not ride vehicle down Ramp. 3. Do not exceed 1,200 lb. capacity, evenly distributed. B

Be sure the tires of the ATV being loaded are not wider than THE • width of the ramps. DO NOT USE this tri-fold ramp to load any vehicle that is carrying • gear on its racks. Do not use this ramp if the tailgate on the vehicle being loaded • is higher than half the ramp’s length. WARNING! All persons not involved in the loading process must stand clear of the loading Ramp and truck. Make sure no pets are nearby. Only use a winch (Not Provided) to load the 4-Wheel ATV. This is the safest way to l

Make sure the Ramp is completely open. Make sure the tailgate the ramp will sit on, is 1. dry and clean. Sit the tongue (angled lip) of the Ramp on the tailgate. Stretch the Safety Chain on each 2. Ramp being used up into the inside of the truck bed; attach the hook on each Safety Chain to a secure attachment point on the inside of the truck bed. WARNING! SAFETY CHAINS MUST BE connected to secure attachment points within the truck bed able to withstand the pulling force of loading. They must als

Safety Warnings and Precautions WARNING: When using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this product! 1. Avoid working alone. If an accident happens, an assistant can bring help. 2. Keep work area clean. Cluttered areas invite injuries. 3. Observe work area conditions. Keep work area well lighted. 4. Keep children away. Children and pets must never be allowed in the area

16. Contact between the tongue of the Ramp and the tailgate of the vehicle, may result in damage to the vehicle’s body finish. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Assembly Your Aluminum Bi-Fold Ramp will require some light

Serious injury and property damage may result. 18. Assure that any load being supported by this jack is well balanced. Unbalanced loads may cause the jack to fall over potentially causing serious personal injury or property damage. SKU 39178 Page 3 19. This jack is not to be used for any aircraft purposes. 20. Jack to be used on a flat, level surface capable of supporting the weight of the jack, the workpiece and related tools Warning:The warnings, cautions, and instructions discussed in this in