AT-MCF2000AC Power Supply Module Note For a list of available chassis models in the AT-MCF2000 media converter product line, contact your Allied Telesis sales representative or visit our web site. 1110-a NORMAL FAULT STATUS PSU FAN Review the following before you begin to install the module in the chassis: . Refer to the chassis’ Installation Guide to verify that the module is appropriate for the unit. . For instructions on how to remove a power supply module, refer to the chassis’s Installation

For The AT- WDRPS- 80 unit can be installed while the multiplexer is powered ON. details on the features and functions of your Allied Telesyn AT-WD1008 chassis and You do not need to power OFF the multiplexer to install the RPS. modules, refer to the following manuals from our web site: . AT-WD1008 Gigabit Ethernet Wavelength Division Multiplexer 1. Loosen the two thumbscrews that secure the blank faceplate over the right- Installation Guide hand redundant power supply expansion slot located on

No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis, Inc. reserves the right to change specifications and other information in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or relate

960 Stewart Drive, Suite B Sunnyvale, CA 94085 USA Tel 1 ( 408) 730- 0950 • Fax 1 (408) 736- 0100 Visit our web site at: alliedtelesyn. com for all of our products. For details on the features and functions of your Allied Note Telesyn AT-WD1008 chassis and modules, refer to the following manuals from our The AT- WDRPS- 10 unit can be installed while the multiplexer is powered ON. web site: You do not need to power OFF the multiplexer to install the RPS. . AT-WD1008 Gigabit Ethernet Wavelength Di

Caution Follow correct anti-static procedures. Failure to do so could damage the PSU, fan, or switch. If you are unsure about correct procedures, contact your authorised Allied Telesis distributor or reseller. Caution When adding or replacing power supplies, keep your hands and fingers out of the power supply bays. After installing a PWR05 power supply, use a screwdriver to tighten the captive screw such that a screwdriver will be required to remove the PSU at a later date. Installation Guide 7

To remove a PSU, chassis fan module or FOM 1. If you are removing a PSU, disconnect the power supply. For AC PSUs, turn off the main power source to the PSU and disconnect the power cord. For DC PSUs, push and release the Run/Standby control to the Standby (off) position. The Run/Standby control is in the Run (on) position when it is depressed, and in the Standby (off) position when it is not depressed. Disconnect the supply cable wires from the circuit breaker. 2. Remove the PSU, chassis fan mo

The RPS can supply power to Allied Telesis switches if the switch’s main power supply fails. Verifying Package Contents Verify that the correct components are included in your package: • AT-PWR3202 Power Supply • One 21-pin D-combo connector cable • This installation guide If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. Warranty The AT-PWR3202 Power Supply has a Lifetime Year Warranty (Five Years Power Supply and Fan). For detailed warranty inf

If the standard power supply fails or loses power, the ATPWR14 module changes from standby to active and provides all power to the system to prevent a network failure. Figure 1. AT-PWR14 Power Supply Module Note The power supply is hot-swappable. You can install it without powering OFF the AT-CV5000 chassis. POWER FAULT AT-PWR14 208 Related Documents This installation guide is an abbreviated version of the installation procedure. For details on the components, features, and functions of this pro

Power supply specifications: ¦ 40 to 60V, 48V nominal ¦ supports either positive grounded or negative grounded operation ¦ a 15Amp certified/listed circuit breaker is required for circuit protection Supply cable specifications: ¦ three-core cable is required ¦ minimum core size: 3.3mm2 (12 AWG) high strand count copper wire ¦ minimum cable rating: 600V, 90 degrees C Warning Disconnect the power supply cable before starting this procedure. 1. Remove the transparent protective terminal cover. 2. S