Votos - 4, Puntuación media: 4.3 ( )

Fabricar: Agri-Fab Tamaño del archivo: 3 mb Nombre del archivo: Idioma del manual:

PART NO. QTY DESCRIPTION 1 23507 1 Wheel Support 2 63917 1 Rear Tongue 3 63155 1 Front Tongue 4 49974 1 Hose Hanger Rod 5 23985 2 Cart Body REF. PART NO. QTY DESCRIPTION 6 41882 1 Hose 7 62458 1 Tailgate Reinforcement Bracket 8 24897 1 Axle 9 24497 1 Latch Stand Bracket 10 42159 2 Wheels 3 1 2 4 8 1211795 10146 13 CARTON CONTENTS (Mow-N-Vac Carton) REF. QTY DESCRIPTION 1 24679 1 Front Panel 2 24678 2 Side Panels 3 44790 1 Rear Door 4 23836 1 Cross Brace 5 43793 2 Hose Clamp 6 23560 1 Adapter Bracket 7 43830 1 Deck Adapter REF. QTY DESCRIPTION 8 64244 1 Poly Hard Top 9 23475 1 Hitch Bracket 10 43791 1 Hose Adapter (Nozzle) 11 46420 1 Elbow 12 N/A 1 Engine w/Base Assembly 13 63376 1 Chipper Chute 14 731-1617 1 Tamper Plug ASSEMBLY This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for proper fuel and engine oil recommendations. 3. Fit the tailgate reinforcement bracket over the end of the cart bed. Position the two door support brackets on the bottom of the reinforcement bracket as shown in figure 2. Fasten the reinforcement bracket and the door supports to the bottom of the cart using four 5/16" x 3/4" truss head bolts and 5/16" nylock nuts. Do not tighten yet. See figure 2. 4. Fasten the tailgate reinforcement bracket to the sides of the cart body using four 1/4" x 5/8" hex bolts and 1/4" nylock nuts. See figure 2. Do not tighten yet. TOOLS REQUIRED FOR ASSEMBLY (1) Screwdriver (1) Pliers (2) 7/16" Wrenches (2) 1/2" Wrench (2) 9/16" Wrenches (2) 3/4" Wrenches (only if figure 23 on page 12 is used) 5/16" NYLOCK NUT1/4" NYLOCK NUT1/4" x 5/8" HEX BOLT5/16" x 3/4" TRUSSHEAD BOLTDOORSUPPORTTAILGATEREINFORCEMENTBRACKET REMOVAL OF PARTS FROM CARTONS 1. Remove the hardware packs and all loose parts from the cartons. 2. Lay out and identify parts shown in carton contents. 3. Lay out and identify parts in the hardware packs. Keep contents of each hardware package separate. ASSEMBLING THE CART BODY 1. Place cart body halves upright on a smooth level surface such as a garage floor or a paved driveway. See figure 1. CAUTION: Do not leave the cart unattended in upright position during assembly. A falling cart can cause personal injury! Pay close attention to the stability of the cart while it remains in an upright position. For best stability, assemble on a smooth level surface. FIGURE 2 5. Pull the cart body halves together. Tighten the four truss head bolts in figure 2. Tighten the four hex bolts in figure 2. Tighten the three hex bolts in figure 1, keeping the bottom aligned and pulled together. 6. Carefully flip the cart end for end so that it rests on the tailgate reinforcement bracket. See figure 3. 2. Assemble cart body halves together using three 1/4" x 5/8" hex bolts and 1/4" nylock nuts as shown in figure 1. Do not tighten yet. 1/4" x 5/8" HEX BOLT1/4" NYLOCK NUT FIGURE 3 FIGURE 1 7. Assemble the wheel support to the bottom of the cart using eight 5/16" x 3/4" truss head bolts and 5/16" nylock nuts as shown in figure 4. Heads of bolts go on the inside of cart. Tighten. 10. Position the rear tongue on the wheel support and the latch stand bracket. Assemble the axle through the wheel support and the tongue. See figure 6. IMPORTANT: Make sure the tongue is securely locked to the latch stand bracket by the latch lock lever. 5/16" NYLOCK NUTWHEELSUPPORT5/16" x 3/4" TRUSS HEAD BOLT AXLETONGUE(REAR) LATCHLOCKLEVER FIGURE 4 FIGURE 6 8. To prevent accidental tipping during the following assembly procedures, lower the cart to rest upside down, with the wheel support facing up, as shown in figure 5. 9. Align the latch stand bracket so that the tab is at the rear. Fasten the bracket to the rear set of holes at the front of the cart using two 1/4" x 5/8" hex bolts, 1/4" flat washers and 1/4" nylock nuts. Use the 1/4" flat washers as shims between the bracket and the cart bed. Make finger tight. See figure 5. 11. Assemble a spacer tube, a 1" flat washer, a wheel (valve stem facing out), and another 1" flat washer onto the axle as shown in figure 7. Secure the wheel with a cotter pin, spreading the ends so that a hub cap can fit over the pin. Assemble the hub cap by pressing it onto the flat washer. Repeat on other end of axle. 12. Pump grease into grease fittings on wheels until grease is forced out through ends of hubs. LATCH STANDBRACKET(Tab at rear) 1/4" x 5/8" HEX BOLT1/4" NYLOCK NUT 1/4" FLATWASHER COTTER PINWHEELHUB CAP1" FLATWASHER1" FLATWASHERAXLESPACER TUBE FIGURE 7 FIGURE 5 13. Flip the cart over so that it rests on its wheels. 14. Assemble the front tongue on top of the rear tongue using three 3/8" x 3" hex bolts and 3/8" nylock nuts. See figure 8. HINT: For easier assembly, support the rear tongue with a block of wood. ASSEMBLING THE VAC 17. Release the latch lock lever and tilt the cart bed back. See figure 10. 18. Assemble the front panel to the cart bed, sliding the bottom lip of the panel in between the cart bed and the latch stand bracket. Fasten the panel to the bottom ...

Descargar ahora

Introduzca dos números de la imagen: