Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Removal of such parts could create a fire hazard. MAINTENANCE AND STORAGE • When this equipment is stopped for servicing, inspection, storage or to change an accessory, make sure the spark plug wire is disconnected from the spark plug and moved away from the spark plug. The machine should be allowed to cool down before making such inspection, ad|ustments, service, etc. Maintain your machine with care and keep it clean for the best and continued safe operation. • Do not use flammable solutions to clean the air filter. • When not in use, your machine should be stored out of the reach of children. Keep where gasoline fumes will not reach an open flame or spark. For long periods of storage, refer to the “Off-Season Storage” section of this manual. ASSEMBLY INSTRUCTIONS ATTACHING THE UPPER GUIDE ASSEMBLY Flat Washer 5/16" I.D. Hex Lock Nut 5/16-18 Thread Hex Bolt -5/16-18 x 8-3/8" Long B IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for proper fuel and engine oil recommendations. NOTE: To determine right and left hand sides of your shredder, stand behind and face the hopper (engine is at the front of the unit). Your shredder has been completely assembled at the factory, except for the hopper assembly (hopper hood and upper guide extension have been sub-assembled), upper guide assembly, chute deflector and the catcher bag. The hardware pack and a pair of safety glasses are also included in the carton. The hardware pack contains the parts shown in figure 1 (shown full size). TO REMOVE SHREDDER FROM CARTON Cut the corners of the carton. Remove all packing inserts. Roll shredder out of carton. Make certain all parts and literature have been removed before the carton is discarded. TOOLS REQUIRED FOR ASSEMBLY (1) Phillips Screwdriver (2) 1/2" Wrenches (one must be a socket wrench) (2) 7/16" Wrenches or Adjustable Wrenches ATTACHING THE HOPPER ASSEMBLY FIGURE 1. 3 I A WARNING: Make certain the spaijk plug wire is disconnected and moved away from the spark plug before assembling the shredder. Spacers (Inside Hinge) Housing Assem bly Chute Def ector FIGURE 2. Hopper Assei nbly Hopper Pivot Assemble ™r\^/ T™“?.c™ws Truss Screw and \'/i Nut First Release Bar Upper Guide Extension Remove T russ ' Upper Screw and Nut Guide Assembly FIGURE 4. ATTACHING THE CHUTE DEFLECTOR (See Figure 2) 1. Remove the hand knobs and cupped washers from each side of the discharge opening on the left side of the shredder. 2. Remove the hex lock nut, two spacers and hex bolt from inside the hinge on the housing assembly. Do not remove one spacer from the hex bolt. —3. Place the chute deflector in position on the discharge opening on the left side of the shredder. Insert hex bolt and spacer through hinge on chute deflector and housing (spacer fits inside of hinge). 4. Place the second spacer over the hex bolt, inside the other part of the hinge. Secure with hex lock nut. Tighten securely. 5. Secure both sides of the chute deflector to the housing using the hand knobs and cupped washers (cupped side of washers go against the chute deflector). A WARNING: Do not operate this shredder unless the chute deflector has been properly installed and is secured with the hand knobs. ATTACHING THE UPPER GUIDE ASSEMBLY (Hardware A) Place upper guide assembly in position on frame, making certain edges of the upper guide assembly are underneath stop washers, and the release bar is -in the slots. See figure 3. Insert hex bolt 8-3/8" long through upper guide assembly and frame. Secure with flat washer 5/16" I.D. and hex lock nut. NOTE: Make certain upper guide assembly can pivot by pulling up on release bar and lowering upper guide assembly. If necessary, loosen hex lock nut a turn or two. Put the upper guide assembly back into the raised position. ATTACHING THE HOPPER ASSEMBLY (Hardware B) Your shredder has been shipped with the upper guide extension attached to the hopper assembly. See fig--ure 4. Attach the hopper assembly to the upper guide assembly as follows. Be certain to place heads of all truss machine screws inside of hopper assembly. 1. Remove one truss machine screw and nut from each side of hopper assembly as shown in figure 4. Push hopper pivot door down inside lower part of hopper as you place hopper assembly (both pieces) inside upper guide assembly. Replace truss screws and nuts just removed, using the front upper hole in assembly as shown in figure 4, one on each side. Tighten finger tight only. 2. Place the six truss machine screws and nuts found in hardware pack in the remaining holes of hopper assembly, alternating sides of the unit and tightening finger tight only. 3. After assembling all eight screws, tighten them securely. 4 ATTACHING THE CATCHER BAG Your shredder is equipped with a catcher bag to catch the shredded material. To attach the bag, place the opening of the bag over the chute deflector so it completely covers the chute ope...
Otros modelos de este manual:Jardín de las trituradoras - 243-645C000 (1.46 mb)