Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
• To attach the bag, place the bag opening over the discharge chute so it completely covers the discharge chute and goes over the chute flanges. • Depress the plunger on the draw-string, and pull on the drew-string until the bag is tight around thechuteopening.Release plungertolockitinto position. See figure 8. Drawstring Bag Figure 8 Read this owner's manual and safety rules before operating your chipper-shredder. Compare the illustration in I figure9withy_urchipper_shreddert_fami_iarizey_urselfwiththe__cati_n_fVari_usc_ntr__sandadjustments_ _1 Save this manual for future reference. I The operation of any chipper-shredder can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses provided w th the chipper-shredder or eye shields before chipping or shredding, or while performing any adjustments or repairs. Discharge Chute Hopper f Chipper Assembly Chute Release Bar Primer Button Throttle Starter Control Handle Figure 9 OPERATING CONTROLS Lower the hopper to collect raked materiat for shredding. Release Bar Chipper Chute Used to release the hopper when raising or lowering. Allows bulky vegetation like stalks or heavy branches Starter Handle upto 3" diameter to be fed into the impeller for chipping and shredding. Used to manually start the engine. Primer Button Throttle Control Fills carburetor with gasoline to aid in starting a cold Regulates speed of the engine. engine. Catcher Bag STOPPING ENGINE Used to collect the shredded material. (not shown) Hopper Assembly Move throttle control lever to STOP position. Allows leaves and small branches upto 0.5 "diameter Disconnect spark plug wire and move away from to be fed into the impeller for chipping and shredding. spark plug to prevent accidental starting. MEETS ANSI SAFETY STANDARDS Searschipper-shreddersconformtothesafetystandardB71.6-1990 oftheAmericanNationalStandardsInstitute. 8 & & WARNING: Before using your chipper- shredder, refer to the safety rules on pages 3 and 4 of this manual again. Always be careful. GAS AND OIL FILL-UP Oil (Packed with unit) • Only use high quality detergent oil rated with API service classification SF, SG or SH. Select the oil's viscosity grade according to your expected operating temperature. Follow the chart below. Co der _ 32°F _ Warmer _.==_.o L 5W30 I SAE 30 NOTE: Although multi-viscosity oils (5W30, 10W30, etc.) improve starting in cold weather, these multiviseosity oils will result in increased oil consumption when used above 32°[::. Check the oil level more frequently to avoid possible engine damage from running low on oil. Fillengine with oil as follows. • Remove dipstick. See figure 10. 1. Remove dipstick end fill oll 2. Remove cap and fill gas F Figure 10 With chipper-shredder on level ground, use a funnel to fill engine with oil to FULL mark on dipstick. Capacity is approximately 20 ounces. Be careful not to overfill. Tilt chipper-shreddertoward the left (from behind the hopper). See figure 11. Check oil level. Put the unit back on the groundcarefully. hand-hold. ,_ WARNING: Do not tilt unit holding the Add oil if necessary. Replace dipstick and tighten. Hold unit this to tilt Figure 11 NOTE: Do not overfill. Oil bottle packed with unit contains 20 oz. of oil. Gasoline Warning: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while instorage. To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE instructions for additional information. Never use engine or carburetor cleaner products inthe fuel tank or permanent damage may occur. Fill gas tank with gas as follows. • Remove fuel cap. See figure 10. • Make sure the container (from which you will pour the gasoline) is clean and free from rust or foreign particles. Never use gasoline that may be stale from long periods of storage inthe container. • Fill fuel tank with fresh, lead-free gasoline. DO NOT use Ethyl or high octane gasoline.Replace fuel cap. WARNING:Do not fill closer than 1/2 inch of top of fuel tank to prevent spills and to allow for fuel expansion. If gasoline is accidently spilled, move chipper-shredder away from area of spill. Avoid creating any source of ignition until gasoline vapors have disappeared. Check the fuel level periodically to avoid running out of gasoline while operating the chipper-shredder. If the unit runs out of gas as it is shredding or chipping, it may be necessary to unclog the unit before it can be restarted. Refer to Removing the Flail Screen in SERVICE AND ADJUSTMENT section. STARTING ENGINE WARNING: Be sure no one other than the operator is standing near the chipper- shredder while starting or operating. Do no...
Otros modelos de este manual:Jardín de las trituradoras - 77587 (909.88 kb)