STARTING ENGINE WARNING: Be sure no one other than the operator is standing near the chipper- shredder while starting or operating. Do not operate this chipper-shredder unless the chute deflector has been properly installed and is secured with the hand knobs. NOTE: To prevent the unit from sliding, place your foot firmly against the wheel. 1. Attach spark plug wire and rubber boot to spark plug. 2. Move starter switch to ON position. 3. Move choke lever to CHOKE position. 4. If restarting a warm

See figure 5. 6. Place upper guide extension in place on guide extension. Secure with four hex screws (B) and hex center lock nuts (C). A 7/16" wrench and adjustable wrench are required. See figure 5. FIGURE 5 5 OPERATION BEFORE STARTING ENGINE 1. Fill fuel tank with fresh regular gasoline. Do Not mix oil with gasoline. 2. Fill crankcase with oil. Refer to separate engine manual packed with your shredder. TO START ENGINE Tecumseh Engine 1. Place control lever (on engine) in "RUN1 posit

5/16" Scr.* 42 11478 Hinge Pin 17 14573 Hopper to Engine Mtg. Plate 43 726-0111 Palnut 3/16" Dia. 18 Engine 44 712-0109 Wing Nut Elastic 1/4-20 Thd. 19 11464 Engine Mounting Plate 45 13431 Blade 20 712-0123 Hex Nut 5/16-24 Thd:* 46 11460-488 Guide Extension Assembly 21 736-0119 L.-Wash. 5/16" Scr.* 47 11472-488 Guide Extension 22 738-0521 Shaft 48 736-0264 FI.-Wash. 5/16" Scr.* N 49 11481-488 Hopper Assembly 23 736-0170 Special L.-Wash. 5/16" I.D. 50 7

Know how to stop the machine and disengage them quickly. 3. Never allow children under 16 years old to operate this machine. Children 16 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent. 4. Never allow adults to operate this machine without proper instruction. 5. Keep bystanders, helpers, pets, and children at least 75 feet from the machine while it is in operation. Stop machine if anyone ent

No. 11). See page 10. 2. Remove bolt (Ref. No. 38), lock washer (Ref. No. 37) flat washer (Ref. No. 36) which holds blade (Ref. No. 45), and blade retainer (Ref. No. 48) to engine crankshaft. See page 10. NOTE Blade is reversible and can be assembled to crankshaft with either side showing. When sharpening blade, follow the original angle of grind as a guide. It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade. An unbalanced bla

Avoid wearing loose fitting clothing. 3. This machine should be operated only upon an earthen level surface. 4. Assure that all screws, nuts and bolts and other fasteners are properly secured. OPERATION 1. When feeding shreddable material into this equipment, be extremely careful that pieces of metal, rocks, bottles, cans or other foreign objects are not included. 2. If the cutting mechanism strikes any foreign object or if your machine should start making an unusual noise or vibration, imm

Solo utilice la maquina para triturar o picar el tipo de material vegetal que se encuentra en un patio normal (es decir, ramas, hojas, ramas pequenas, etc.) Evite las plantas fibrosas, por ejemplo, las de tomate, hasta que esten totalmente secas. Pueden ingresar al canal de la cortadora ramas pequenas de hasta 3” de diametro (2” en el caso del modelo serie 450). Como bajar el montaje de la tolva 1. Con una mano tome la manija que se encuentra en la parte superior del montaje de la tolva y levant