Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
CAUTION Before using any product to test your blood glucose (blood sugar), read all instructions and practise the test. Do all quality control checks as directed and consult with a diabetes healthcare professional. The One Touch™ Profile™ System is intended for use outside the body (in vitro diagnostic use). It should be used only for testing purposes and only with whole blood (not plasma or serum). It should not be used for the diagnosis of diabetes and has not been validated for testing the blood of newborns. The One Touch Profile System contains many small parts which may be dangerous if swallowed. It is therefore best to keep the system away from small children. 1 TABLE OF CONTENTS TABLE OF CONTENTS Introduction 4 Precautions and limitations 5 One Touch™ Profile™ Blood Glucose Meter 6 One Touch™ Test Strips 8 SETTING THE SYSTEM TESTING YOUR BLOOD Coding the meter Check strip test Control solution test Getting a drop of blood Step- by- step test procedure Event labelling 10 12 16 22 29 35 USING THE METER MEMORY CHANGING METER SETTINGS Entering the memory Recalling results Entering the set-up (options) mode Beep prompts 2 37 38 40 42 Time and date 43 Event averaging 44 Insulin prompt 45 Insulin programming 46 Display language 48 Time format 49 Date format 49 Decimal separator 50 Unit of measure 51 Exiting the set-up mode 51 SOLVING PROBLEMS Test procedure messages 52 Error messages 56 TAKING CARE OF YOUR METER Cleaning the meter 63 Replacing the batteries 66 SPECIFICATIONS Performance characteristics 69 Warranty 70 Insulin Types 71 3 INTRODUCTION The One Touch™ Profile™ Glucose Monitoring System is for people with diabetes who need to check the level of glucose (sugar) in their blood. To perform a blood glucose test, a One Touch™ Test Strip is inserted into the meter and a small sample of blood is applied to the test strip. The meter then measures the blood glucose level and displays the result in just 45 seconds. Easy-tounderstand symbols guide you through the test procedure and help you if any problems arise. 4 The One Touch Profile Glucose Monitoring System consists of three main products: The One Touch™ Profile™ Blood Glucose Meter, One Touch Test Strips and One Touch™ Normal Control Solution. For reliable results and to maintain the manufacturer’s total service, support, and warranty, use only One Touch™ Profile™ System products made by LifeScan. PRECAUTIONS AND LIMITATIONS • If you experience symptoms that are not consistent with your blood glucose results, and you have carefully followed the procedure described in your owner’s booklet, contact your healthcare professional immediately. • DO NOT make significant changes to your medication program or ignore physical symptoms without consulting your healthcare professional. • If the message HI DANGER appears on the meter display, this indicates severe high blood sugar (hyperglycemia); contact your doctor immediately. • Note that extremes in whole blood hematocrits, above 60% or below 25%, can cause false low results. • Reducing substances, such as Vitamin C (ascorbic acid), have little effect on blood glucose results when found in normal blood concentrations. However, abnormally high concentrations of reducing substances in blood will cause false low test results. • DO NOT use blood samples with preservatives that contain fluoride (in gray top test tubes). You will get false low results. • When testing, removal of the test strip prior to display of the blood glucose result may give you a false result. 5 ONE TOUCH™ PROFILE™ BLOOD GLUCOSE METER Study this diagram to become familiar with all of the parts of your One Touch™ Profile™ Meter. Battery Compartment (on back) M Button Data Port On/Off Button 6 CM Holder Display C Button Test Strip Test Area with protective coating On/off button. This button turns the meter on and off. Display. This is where you read the simple messages that guide you through testing, setting options, and using the memory. Your test results will be displayed here. M Button. The One Touch™ Profile™ Meter automatically stores your test results. Use the M button to recall the information stored in your meter’s memory and to review your meter’s set-up options. C Button. Use the C button to set the code on the One Touch Profile Meter and to change the meter’s set-up options. Test strip holder. The test strip holder holds a One Touch™ Test Strip in place when you perform a blood glucose or control solution test. Test area. The test area is located under the test strip holder. Battery compartment. Holds two AAA batteries. The batteries are already installed in your meter. Data port. Allows you to transfer the information stored in the meter’s memory to a computer to view, analyse, and print. Please call your authorized LifeScan representative for more information about our Diabetes Management System software. 7 ONE TOUCH™ TEST STRIPS When blood is applied to the white test spot on the test strip, compounds on the test strip react with th...